Beisler 100-54 - Manual (Page 56)

3-2
2.10.2 Setting the distances .......................................................................................... 3-16
2.10.3 Light cross size .................................................................................................. 3-16
2.10.4 Setting the focus ................................................................................................ 3-16
2.10.5 Installing and removing mark lamps ................................................................... 3-16
2.10.6 Replacing the mask ........................................................................................... 3-16
2.11 Stamp ................................................................................................................ 3-17
2.12 Flap clamp adjustment ....................................................................................... 3-17
2.12.1 Flap clamp pressure .......................................................................................... 3-17
2.12.2 Flap clamp height .............................................................................................. 3-17
2.12.3 Parallelism to the folder ..................................................................................... 3-17
2.13 Piping cutter adjustment .................................................................................... 3-18
2.13.1 Replacing knives ................................................................................................ 3-18
2.13.2 Setting the pipe length ....................................................................................... 3-18
2.13.3 Piping cutter center position ............................................................................... 3-18
3 Adjustments at the sewing head .................................................................... 3-17
3.1 Height adjustment .............................................................................................. 3-17
3.2 Lateral adjustment ............................................................................................. 3-17
3.3 Driving belt tension of the sewing motor ............................................................ 3-17
3.4 Top threat cutter (Beisler sewing head) .............................................................. 3-18
3.5 Height of top threat catcher ................................................................................ 3-18
3.6 Center knife adjustments ................................................................................... 3-18
3.6.1 Switching on ...................................................................................................... 3-18
3.6.2 Switching off ...................................................................................................... 3-18
3.6.3 Safety initiator at the center knife pole ............................................................... 3-18
3.6.4 Depth adjustment of the safety initiator .............................................................. 3-18
3.6.5 Height of center knife ......................................................................................... 3-19
3.6.6 Shear angle of the center knife ......................................................................... 3-19
3.6.7 Lateral adjustment ............................................................................................. 3-19
3.6.8 Needle protection ............................................................................................... 3-19
3.7 Adjustments of the bobbin threat catcher (Beisler sewing head) ....................... 3-20
3.7.1 Catcher adjustment ............................................................................................ 3-20
3.7.2 Time of bobbin threat cutting .............................................................................. 3-20
3.7.3 Duration of bobbin threat cutting ....................................................................... 3-20
3.8 Sensitivity of the bobbin detector (option) ........................................................ . 3-20
3.9 Clean tactual head of the bobbin detector (option) ............................................ 3-21
3.10 Adjust piping detection ....................................................................................... 3-21
3.10.1 Lateral adjustment . ........................................................................................... 3-21
3.10.2 Adjust intensity ................................................................................................... 3-21
3.11 Swing up sewing head ...................................................................................... 3-22
3.12 Upper threat monitor ......................................................................................... 3-22
3.12.1 Switch on time ................................................................................................... 3-22
3.12.2 Filter threat monitor ........................................................................................... 3-22
4 Adjustments at the mitre knifes ...................................................................... 3-23
4.1 Basic adjustment locked mitre knife (seam end) ................................................ 3-23
4.2 Basic adjustment movable mitre knife (seam start) ............................................ 3-23
4.3 Mitre knife height ............................................................................................... 3-23
4.4 Mitre knife broadth ............................................................................................. 3-23
4.5 Pre-stabber ........................................................................................................ 3-24
4.6 Lateral adjustment ............................................................................................. 3-24
4.7 Fine adjustment in the length ............................................................................. 3-24
4.8 Tighten cog-belt of the mitre knife drive ............................................................. 3-24
5 Adjustment of machine options ..................................................................... 3-25
5.1 Automatic push-back blocking ........................................................................... 3-25
5.2 Height of the take off roller ................................................................................. 3-25
5.3 Mitre knife slant position .................................................................................... 3-26
5.3.1 Distance between basic bodies ......................................................................... 3-26
5.3.2 Height adjustment ............................................................................................. 3-26
5.3.3 Center adjustment ............................................................................................. 3-26
5.3.4 Adjust mitre knife stops ...................................................................................... 3-26
5.3.5 Knife arrangement ............................................................................................. 3-26