Flowserve 500+ Series Logix User Manual
User instructions, Installation operation maintenance safety manual, Logix
Advertising
Table of contents
Document Outline
- 1.1 Using This Document
- 1.2 Terms Concerning Safety
- 1.3 Protective Clothing
- 1.4 Qualified Personnel
- 1.5 Valve and Actuator Variations
- 1.6 Spare Parts
- 1.7 Service / Repair
- 1.8 Basic Operation
- 1.9 HART
- 1.10 Position Definition
- 1.11 Command Input and Final Command
- 1.12 Outer Loop
- 1.13 Inner Loop
- 1.14 Detailed Sequence of Positioner Operations
- 1.15 Inner Loop Offset
- 2 SPECIFICATIONS
- 2.1 Input Signal
- 2.2 Air Supply
- 2.3 Pneumatic Output
- 2.4 Stroke Output
- 2.5 Analog Output – Multi-Function Card
- 2.6 Remote Mount Specifications
- 2.7 Limit Switch Specifications
- 2.8 Positioner Performance Characteristics
- 2.9 Physical Specifications
- 2.10 Temperature
- 2.11 ValveSight DTM Software Specifications
- 3 HAZARDOUS AREA CERTIFICATIONS
- 4 STORAGE AND UNPACKING
- 5 MOUNTING AND INSTALLATION
- 6 TUBING
- 7 ELECTRICAL CONNECTIONS
- 8 STARTUP
- 9 POSITIONER FUNCTIONS (No Display Required)
- 10 POSITIONER FUNCTIONS (LCD Display)
- 10.1 Main Display View
- 10.2 Menu Overview
- 10.3 Menu Features
- 10.3.1 Status
- 10.3.2 Alerts and Alarms
- 10.3.3 Partial Stroke Test
- 10.3.4 Calibration
- 10.3.5 Configuration (Positioner Tuning)
- 10.3.6 Configuration (Characterization)
- 10.3.7 Configuration (Pressure Control)
- 10.3.8 Configuration (Soft Limits and Shutoff)
- 10.3.9 Configuration (Set Time and Date)
- 10.3.10 Configuration (User Preferences)
- 10.3.11 Configuration (Burst Mode)
- 10.3.12 Configuration (Positioner Revs)
- 10.3.13 Configuration (Factory Reset)
- 10.3.14 Card 1 (or Card 2)
- 10.3.15 Language
- 11 HART COMMUNICATION
- 12 MODEL FEATURES
- 13 MULTI-FUNCTION CARD
- 14 LIMIT SWITCHES
- 15 REMOTE MOUNT
- 16 REQUIREMENTS FOR SAFETY INTEGRITY
- 16.1 Fail Safe State
- 16.2 Safety Function
- 16.3 Fail Safe State Response Time
- 16.4 Positioner Model Selection and Specification
- 16.5 Installation
- 16.6 Required Configuration Settings
- 16.7 Maximum Achievable SIL
- 16.8 Reliability data
- 16.9 Lifetime limits
- 16.10 Proof Testing
- 16.11 Maintenance
- 16.12 Repair and replacement
- 16.13 Training Requirements
- 17 MAINTENANCE AND REPAIR
- 17.1 Scheduled Maintenance
- 17.2 Required Tools and Equipment
- 17.3 Torque Specification for Screws
- 17.4 Installing a Limit Switch
- 17.5 Replacing the LCD Board
- 17.6 Replacing an Auxiliary Card
- 17.7 Replacing a Main Board
- 17.8 Replacing the Pressure Sensor Board
- 17.9 Cleaning and Replacing a Double Acting Pilot Relay
- 17.10 Replacing a Single Acting Pilot Relay
- 18 TROUBLESHOOTING
- 19 POSITIONER DIMENSIONS
- 20 HOW TO ORDER