Document Outline

• FOREWORD
• SAFETY ALERT SYMBOLS AND SAFETY SIGNAL WORDS
  • Contact:
  • In USA:
  • Outside USA:
• REVISION LOG
• SECTION 1. SAFETY PRECAUTIONS
  • 1.1 GENERAL
  • 1.2 PRE-OPERATION
    • Operator Training and Knowledge
    • Workplace Inspection
    • Machine Inspection
  • 1.3 OPERATION
    • General
    • Trip and Fall Hazards
    • Electrocution Hazards
    • Tipping Hazards
    • Crushing and Collision Hazards
  • 1.4 TOWING, LIFTING, AND HAULING
  • 1.5 Maintenance
    • Maintenance Hazards
    • Battery Hazards
• SECTION 2. USER RESPONSIBILITIES, MACHINE PREPARATION AND INSPECTION
  • 2.1 PERSONNEL TRAINING
    • Operator Training
    • Training Supervision
    • Operator Responsibility
  • 2.2 PREPARATION, INSPECTION, AND MAINTENANCE
  • 2.3 PRE-START INSPECTION
  • 2.4 DAILY WALK-AROUND INSPECTION
  • 2.5 FUNCTION CHECK
• SECTION 3. MACHINE CONTROLS, INDICATORS AND OPERATION
  • 3.1 GENERAL
  • 3.2 DESCRIPTION
  • 3.3 OPERATING CHARACTERISTICS AND LIMITATIONS
    • General
    • Placards
  • 3.4 PLATFORM LOADING
  • 3.5 MACHINE CONTROL LOCATIONS
  • 3.6 BATTERY CHARGING
    • Battery Charger Fault (LED Flash)
  • 3.7 GROUND CONTROL STATION
    • Ground Emergency Stop Switch - (Item 3 - Figure 3-3.)
    • Key Selector Switch - (Item 2 - Figure 3-3.)
    • Platform Lift/Lower Switch - (Item 1 - Figure 3-3.)
    • MDI-Indicator - (Item 4 - Figure 3-3.)
    • Overload Indicator - (Item 5 - Figure 3-3.)
  • 3.8 SCISSOR ARM - SAFETY PROP
  • 3.9 PLATFORM CONTROL STATION
    • Platform Emergency Stop Switch - (Item 8 - Figure 3-7.)
    • Lift/Drive Select - (Item 10 - Figure 3-7.)
    • Forward/Reverse/Lift/Lower Direction Decal - (Item 4 - Figure 3-7.)
    • Drive/Lift/Steer Joystick Control
    • Steering And Traveling
    • Steering
    • Traveling Forward and Reverse
    • Raising And Lowering Platform
    • Overload Indicator -
    • Tilt Indicator Warning Light and Alarm
    • Horn
    • Low Battery Charge and System Fault Indicator
    • Alarm
  • 3.10 PLATFORM EXTENSION
  • 3.11 PARKING AND STOWING MACHINE
    • Anti-Vandalism Package - Option
  • 3.12 MACHINE LIFTING AND TIE DOWN
    • Lifting
    • Tie Down
  • 3.13 TOWING
    • Electric Brake Release
    • Mechanical Brake Release
• SECTION 4. EMERGENCY PROCEDURES
  • 4.1 GENERAL INFORMATION
  • 4.2 EMERGENCY OPERATION
    • Operator Unable to Control Machine
    • Platform Caught Overhead
    • Righting of Tipped Machine
  • 4.3 PLATFORM MANUAL DESCENT
  • 4.4 INCIDENT NOTIFICATION
• SECTION 5. GENERAL SPECIFICATIONS AND MAINTENANCE
  • 5.1 INTRODUCTION
    • Other Publications Available Specific to this Machine:
  • 5.2 OPERATING SPECIFICATIONS
    • Platform Capacities
    • Machine Dimensional Data
    • Tires
    • Batteries
    • Electrical System
  • 5.3 CRITICAL STABILITY WEIGHTS
  • 5.4 LUBRICATION
    • Lubrication Capacities
    • Hydraulic Oil
    • Lubrication Specifications
  • 5.5 MAINTENANCE
    • Hydraulic Oil Check Procedure
  • 5.6 BATTERY MAINTENANCE
    • Battery Maintenance and Safety Practices
    • Battery Quick-Disconnect
  • 5.7 TIRES AND WHEELS
    • Tire Wear and Damage
    • Wheel and Tire Replacement
    • Wheel Installation
  • 5.8 DECAL INSTALLATION
  • 5.9 DIAGNOSTIC TROUBLE CODES (DTC)
  • 5.10 DTC CHECK TABLE INDEX
  • 5.11 DIAGNOSTIC TROUBLE CODES (DTC) CHECK TABLES
    • 0-0 Help Comments
    • 2-1 Power-Up
    • 2-2 Platform Controls
    • 2-3 Ground Controls
    • 2-5 Function Prevented
    • 3-1 Line Contactor Open Circuit
    • 3-2 Line Contactor Short Circuit
    • 3-3 Ground Output Driver
    • 4-2 Thermal Limit (SOA)
    • 4-4 Battery Supply
    • 6-6 Communication
    • 7-7 Electric Motor
    • 8-2 LSS - Load Sensing System
    • 8-4 Elevation Switch
    • 9-9 Hardware
• SECTION 6. INSPECTION AND REPAIR LOG