Document Outline

• Chapter 1: Introduction
  • The Complete Category 5 Solution
  • 2-Way Injector +/2-Way Injector
  • Super Injector +/Super Injector
  • Scanner Display Conventions
  • On-Line Help for Instant Answers
• Chapter 2: Getting Started
  • Charging the Scanner’s Battery
  • Ready Screen
  • Scanner Information
  • Ni-Cd Battery (Scanner and 2-Way Injectors)
  • 2-Way Injector+/2-Way Injector Battery
  • Ni-Cd Battery Tips
  • Battery Refresh Mode
  • Super Injector+/Super Injector Battery
  • Test Connectors
  • High Voltage Protection
  • 2-Way Injector+/2-Way Injector LED Indicators
  • Super Injector+/Super Injector LED Indicators
  • When to Use the Injector
  • Using Multiple Injectors
  • Injector Calibration
  • Mod 8 Adapter Note
  • Calibration Connections
  • Injector Internal Calibration (2-Way Injector+/2-Way Injector only)
  • Connections
  • Basic Link with Modular 8 Jacks
  • Basic Link with IDC Block and Modular 8 Jack
  • Full Channel Modular 8 Link
• Chapter 3: Autotest
  • Steps for Running Autotest
  • Selecting the Cable Type
  • Editing the Cable Type
  • Calculating NVP
  • Customizing Autotest
  • Editing Autotest Information
  • Editing the Autotest Name
  • Selecting Pairs for Autotest
  • Selecting Tests to Run During Autotest
  • Editing Test Limits
  • Running Autotest
  • Autotest Results Screen
  • Viewing Autotest Results
    • Wire Map
      • Wire Map Test Results
    • Length
      • Customizing Length Limits
      • Length Test Results
    • Propagation Delay
      • Customizing Delay Limits
      • Propagation Delay Test Results
    • Near End Crosstalk (NEXT)
      • Measuring NEXT at Both Ends of the Link
      • Customizing NEXT Limits
      • NEXT Test Results
      • NEXT Detail
      • NEXT Graph
    • Attenuation
      • Customizing Attenuation Limits
      • Attenuation Limits and Frequency
      • Editing Attenuation Limits
      • Attenuation Test Results
      • Attenuation Detail
      • Attenuation Detail
      • Attenuation Graph
    • Attenuation-to-Crosstalk Ratio (ACR)
      • Customizing ACR Limits
      • ACR Test Results
    • Impedance
      • Customizing Impedance Limits
      • Impedance Test Results
    • Loop Resistance
      • Customizing Loop Resistance Limits
      • Loop Resistance Test Results
    • Capacitance
      • Customizing Capacitance Limits
      • Capacitance Test Results
  • Saving Autotest Results
  • Save Sweep Data
  • Printing Autotest Results
    • PRINT FORMAT
    • Viewing Autotest Results Summary
    • Sample Autotest Report
• Chapter 4: Editing, Printing & Updating
  • Editing with the Alphanumeric Keypad
  • Editing with the Arrow Keys
  • Printing or Downloading Test Results
  • Connection for Printing Test Results
  • Connection for Downloading Test Results
  • Printing Tips
  • Uploading Autotest Reports to Windows Terminal
  • Uploading Autotest Reports to a PC with Procomm Plus
    • Procomm Plus for DOS
    • Procomm Plus for Windows
  • Uploading NEXT and Attenuation Graphs to a PC with Procomm Plus
    • Procomm Plus for DOS
    • Procomm Plus for Windows
  • Troubleshooting Printing Problems
  • Downloading Software Updates
  • Updating Scanner Software from the PC
  • Updating the 2-Way Injector+/2-Way Injector
  • Technical Support
  • World Wide Web
  • Microtest Bulletin Board System (BBS)
  • FaxFacts
• Chapter 5: Find Cable Faults
  • Wire Map
  • Wire Map for Both Ends of the Link
• Chapter 6: Measure Cable Performance
  • NEXT
    • NEXT Graph
    • NEXT Sweep
  • Attenuation
    • Attenuation Graph
    • Attenuation Limits
  • Length/Delay
  • Impedance
  • Loop Resistance
  • Capacitance
  • Noise
  • Impulse Noise
  • Peak-to-Peak Noise
• Chapter 7: Analyze LAN Traffic
  • LAN Traffic Display
  • Setting Up the Traffic Monitor
• Chapter 8: Extended Functions
  • Extended Functions Menu
  • Autotest Memory
  • Autotest Setup
  • Editing Autotest Information
  • Calibrating the Injector
  • Setting Up User Preferences
  • Editing Owner/Company Name
  • Setting Backlight and Auto Shutoff Times
  • Setting Up Units
  • Setting Up the Printer Port
  • Selecting a Graphics Printer
  • Setting the Date and Time
  • Displaying Injector Information
  • Tracing a Cable
  • Locating an Office Cable Drop
• Appendix A: Specifications
  • PentaScanner+/PentaScanner/PentaScanner Cable Admin
  • 2-Way Injector+/2-Way Injector
• Appendix B: 150 ohm Cables
  • Working with 150 Ohm Cables
  • Creating a Cat 5 Test for Token Ring
• Appendix C: Cable Pin-outs
  • Cable Pin-Out Signals
• Appendix D: Working with Coaxial Cable
  • Length/Delay Test Results
  • Impedance Test Results
  • Loop Resistance Test Results
  • Capacitance Test Results
  • Impulse Noise Test Results
  • Peak-to-Peak Noise Test Results