Panasonic WJ-HD309 - Manual (Page 118)

118
8 Baud Rate
Select the communication speed for data transmission with
a connected device from the following.
4 800/9 600/19 200 bps
8 Control Camera CH
It is possible to assign camera channels to the RS485 ports
1 and 2 as shown below.
[Screenshot 1]
Start operation from the "RS485 Setup" menu.
z Move the cursor to "Control Camera CH" using the
arrows button (C D) and press the SET button.
[Screenshot 2]
The "Control Camera CH" pop-up window will be displayed.
x Move the cursor to a desired cell in the "TERM" column
using the arrows button.
[Screenshot 3]
The cursor will move to the selected cell in the "TERM" col-
umn.
c Select a port by rotating the jog dial.
PORT 1: Control through the RS485 port 1.
PORT 2: Control through the RS485 port 2.
Repeat steps 2 and 3 to assign other camera channels
to be controlled through the RS485 ports.
v Move the cursor to "OK" using the arrows button and
press the SET button.
→ Camera channels and ports to be controlled will be
assigned and the "Control Camera CH" menu will be
closed.
Notes:
• When you move the cursor to "CANCEL" in step 4
and press the SET button, the settings will be can-
celed and the "Camera Number Setup" menu will be
closed.
• The unit number of the camera will be congruent
with the camera number.
8 Data Bit
The data length for communication will be displayed.
It is impossible to change the value for this setting.
8 Parity
Methods to check a transmission error at communication
will be displayed.
It is impossible to change the value for this setting.
8 Stop Bit
Number of stop bit will be displayed.
It is impossible to change the value for this setting.
● [RS232C Setup] Settings for RS232C
Perform the following settings for RS232C.
8 Unit Address(System)
A unit address (System) is a unique number assigned to
each system device. The addresses must be unique to
identify system devices when connecting multiple system
devices.
Numbers, "001"-"099", are to be assigned as the unit
addresses for the system devices.
8 Baud Rate
Select the communication speed for data transmission with
a connected device from the following.
9 600/19 200/38 400 bps
Schedule
System Comm Switcher
SETUP MENU
LIVE
Maintenance Recording Event
Display
Camera Control
PS.DATA Setup
RS485 Setup
RS232C Setup
NW Setup 1
NW Setup 2
NTP Setup
■ Baud Rate
■ Control Camera CH
■ Data Bit
■ Parity
■ Stop Bit
19200
8
1
NONE
SETUP
Schedule
System Comm Switcher
SETUP MENU
LIVE
Maintenance Recording Event
Display
Camera Control
PS.DATA Setup
RS485 Setup
RS232C Setup
NW Setup 1
NW Setup 2
NTP Setup
■ Baud Rate
■ Control Camera CH
■ Data Bit
■ Parity
■ Stop Bit
19200
8
1
NONE
SETUP
O K CANCEL
■ Control Camera CH
CAMERA
CAM1
CAM2
CAM3
CAM4
CAM5
CAM6
CAM7
CAM8
CAMERA
CAM9
CAM10
CAM11
CAM12
CAM13
CAM14
CAM15
CAM16
TERM
PORT2
PORT2
PORT2
PORT2
PORT2
PORT2
PORT2
PORT2
TERM
PORT1
PORT1
PORT1
PORT1
PORT1
PORT1
PORT1
PORT1 PORT1
Schedule
System Comm Switcher
SETUP MENU
LIVE
Maintenance Recording Event
Display
Camera Control
PS.DATA Setup
RS485 Setup
RS232C Setup
NW Setup 1
NW Setup 2
NTP Setup
■ Baud Rate
■ Control Camera CH
■ Data Bit
■ Parity
■ Stop Bit
19200
8
1
NONE
SETUP
O K CANCEL
■ Control Camera CH
CAMERA
CAM1
CAM2
CAM3
CAM4
CAM5
CAM6
CAM7
CAM8
CAMERA
CAM9
CAM10
CAM11
CAM12
CAM13
CAM14
CAM15
CAM16
TERM
PORT2
PORT2
PORT2
PORT2
PORT2
PORT2
PORT2
PORT2
TERM
PORT1
PORT1
PORT1
PORT1
PORT1
PORT1
PORT1
PORT1 PORT1
Schedule
System Comm Switcher
SETUP MENU
LIVE
Maintenance Recording Event
Display
Camera Control
PS.DATA Setup
RS485 Setup
RS232C Setup
NW Setup 1
NW Setup 2
NTP Setup
■ Unit Address(System)
■ Baud Rate
■ Data Bit
■ Parity
■ Stop Bit
■ Retry Timing
001
8
1
OFF
NONE
9600