Panasonic WJ-HD309 - Manual (Page 162)

162
General
SPECIFICATION
Power source:
Power consumption
Ambient operating
temperature
Ambient operating
humidity
Dimensions
Weight
Input/Output
Video
Audio
Others
* 1 When power is not supplied, the video output signal was not sent from the unit even if a video input signal is supplied.
* 2 Non-voltage N.O. Contact, 100 mA, +5 V pull-up
* 3 Open collector output, maximum under conditions of 24 V DC and 100 mA or less
* 4 High (+12 V, 6.3 mA)
* 5 30 K Ω, 5 V pull-up, –100 mA, N.O. Contact
* 6 5 V pull-up, –100 mA, Non-voltage N.O. Contact input
* 7 200 mA at maximum
* 8 Changeable with the mode switch
Video input connectors
Cascade input connector
Video output connectors
Monitor output connectors
Monitor output connector
(VGA)
S-video output connector
Video output connector
(front panel)
Audio input connectors
Expansion connector
Audio output connectors
Copy connectors
Control connectors
Alarm port
RS-485 ports
DATA ports
SERIAL connector
Ethernet port
220 V - 240 V AC, 50 Hz
85 W
+5 °C to +45 °C (41 °F - 113 °F)
Less than 85 %
420 mm (W) X 88 mm (H) X 350 mm (D) [16-9/16" (W) X 3-7/16" (H) X
13-3/4" (D)] (excluding rubber feet and projections)
9.5 k g (21 lbs.)
1 V [P-P] / 75 Ω, with auto termination loop-thru, vertical timing pulse mul-
tiplexed, x8 (1 to 8 CH) (BNC)
1 V [P-P] / 75
Ω, with auto-termination loop-thru,
x8 (9 to 16 CH) (BNC)
1 V [P-P] / 75 Ω (BNC)
1 V [P-P] / 75 Ω, active loop-thru output, x8 (1 to 8 CH) (BNC)*
1
1 V [P-P] / 75 Ω, active loop-thru output, x8 (9 to 16 CH) (BNC)
1 V [P-P] / 75 Ω, x2 (BNC)
RGB output, x1 (15-pin D-sub)
Y = 1 V [P-P] / 75 Ω, C=0.286 V [P-P] / 75 Ω, x1 (S-video output connec-
tor)
1 V [P-P] / 75 Ω, x1 (RCA pin)
–10 dB, 10 K
Ω, x4 (RCA pin)
High-speed serial interface, 480 Mbps (theoretical value), x1
High-speed serial interface, 480 Mbps (theoretical value), x2
Emergency recording input* 2 , additional space warning output* 3 (for
devices connected to copy connectors), HDD trouble output* 3 , camera
trouble output* 3 , trouble output* 3 , electricity failure recovery completion
output* 4 , time adjust input/output* 5 , sequence switching input/output* 5 ,
electricity failure detection input* 2 , external recording mode switching* 2
(25-pin D-sub) , +5 V output * 7
1 to 8 CH alarm input* 6 , 1 to 16 CH alarm input* 2 , 1 to 16 alarm output* 3 ,
alarm recovery input* 2 , alarm suspension input* 5 (25-pin D-sub)
RS-485 (full duplex/half duplex* 8 ), x2 (RJ-11)
RS-485, x2 (RJ-11)
RS-232C, x1 (9-pin D-sub)
10 Base-T/100 Base-Tx (RJ-45)
–10 dB, 600
Ω, unbalanced, x2 (RCA pin)