Rockwell Automation GV3000/SE AC Drive ControlNet Network Communication Board, M/N 2CN3000 - Manual (Page 96)

7-6 GV3000/SE AC Drive ControlNet Network Communication Option Board
Table 7.2 – File N11:X (Drive Display Data (Read Only))
File
Address Name Description
N11:0 Fault Word 1 This element displays the status of the drive fault bits. Some are vector (v),
some are V/Hz (h), and some are common to both regulators(c).
b00 Overcurrent (c)
b01 Overcurrent Accelerating (c)
b02 Overcurrent Decelerating (c)
b03 DC Braking Fault (h)
b04 HIgh DC Bus (c)
b05 Low DC Bus (c)
b06 Electronic Thermal Overload (c)
b07 Overtemperature (c) b08 Function Loss (c)
b09 Check Sum Failed (c)
b10 Loss of Serial Communication (c)
b11 Serial Port Spurious Interrupt (c)
b12 Self Tune Failed (u)
b13 Overspeed (u)
b14 Motor Phase Loss (c)
b15 Overfrequency (c)
N11:1 Fault Word 2 This element displays the status of the drive fault bits. Some are vector (v),
some are V/Hz (h), and some are common to both regulators(c).
b00 Network Communication Loss (c)
b01 Bypass Contact (c)
b02 HIgh Time ID Aborted (h)
b03 Drive ID Aborted (c)
b04 High Line (h)
b05 EEPROM Write Failed (c)
b06 PU Overload (c)
b07 Ground Current (c) b08 Asymmetrical Bus (c)
b09 MIssing PU Connector (c)
b10 PU Not Selected (c)
b11 Input Phase Loss (c)
b12 Encode Loss (u)
b13 Analog Input 4-20 mA Loss
b14
b15 Fatal System Error (c)
N11:2 Motor Speed This element displays drive speed as scaled by P.028.
N11:3 Motor Volts This element displays motor voltage, where 460 = 460 VAC)
N11:4 Motor Amps This element displays motor current, where 150 = 15.0 amps)
N11:5 Motor KW This element displays motor kilowatts, where 150 = 1.50 kW.
N11:6 Motor Torque This element displays torque, where 100 = 100%.
N11:7 Power Factor This element displays power factor, where 10000 = 1.0
N11:8 Error Log Count This element displays the number of entries in the error log.
N11:9 Error Log 0,1 These elements display the drive error log packed in bytes. For example:
N11:8 = 3; the value 3 indicates there are 3 errors in the error log.
N11:9 = 0408; the value 04 in the upper byte indicates that the first error is a
High DC Bus. The value 08 in the low byte indicates that the second
error is a Function Loss. Hex values 00 - 0F correspond to Fault Word
1 above, bits b00 - b15. Hex values 10 - 1F correspond to Fault Word
2 above, bits b00 - b15. See the
GV3000/SE Software Reference for a
listing of drive fault codes.
N11:10 = 1Bxx; the value 1B in the upper byte indicates that the third error is
an Input Phase Loss.
N11:10 Error Log 2,3
N11:11 Error Log 4,5
N11:12 Error Log 6,7
N11:13 Error Log 8,9
N11:14 Secondary
Status Bits b00 OCL Enabled (vector only)