Rice Lake IQ 700 Configurable Weight Indicator - Manual (Page 22)

18 IQ 700 Installation Manual
3.1.4 Normal Configuration Setup Parameters
You must be in the configuration mode (SW 2 closed to set the indicator from the PC) to be able to write
configuration parameters. To write commands the following
Jxxyyzz<CR> sequence must be used. The following
parameters and their setup numbers are as follows:
Parameter 1 = Grads J0600 03 = Both J1100 02 = Ov.Un J1103 06 = 6 J1200 14 = 50
J0100 00 = 500 J1101 00 = HL J1103 07 = 7
J0100 01 = 1000 Parameter 7 = AZM Capture J1101 01 = TGT J1103 08 = 8 Parameter 13 = Truck in/out
J0100 02 = 1500 J0700 00 = Off J1103 09 = 9 J1300 00 = Nor
J0100 03 = 2000 J0700 01 = .5 J1102 00 = Pos J1103 10 = 10 J1300 01 = Tru
J0100 04 = 2500 J0700 02 = 1 J1102 01 = Zer J1301 00 = Can
J0100 05 = 3000 J0700 03 = 3 J1103 00 = Off J1301 01 = Str
J0100 06 = 4000 J1103 00 = Pos J1103 01 = 1
J0100 07 = 5000 Parameter 8 = Zero Range J1103 01 = Zer J1103 02 = 2 J1302 00 = Off
J0100 08 = 6000 J0800 00 = 1.9 J1103 03 = 3 J1302 01 = On
J0100 09 = 8000 J0800 01 = FS J1104 00 = Pos J1103 04 = 4.
J0100 10 = 10000 J1104 01 = Zer Parameter 14 = Serial
J0100 11 = 12000 Parameter 9 = Motion Band J1104 00 = Off J1400 00 = Off
J0100 12 = 14000 J0900 00 = Off J1100 03 = Bat 1 J1104 01 = S1 J1400 01 = SI
J0100 13 = 16000 J0900 01 = 1 J1101 00 = Off J1104 02 = S1.P J1400 02 = DU
J0100 14 = 18000 J0900 02 = 3 J1101 01 = S1 J1104 03 = S1.D (J1401 – 1405 for SI and DU)
J0100 15 = 20000 J0900 03 = 5 J1101 02 = S1.P J1104 04 = S.P.D. J1401 00 = Net
J0900 04 = 10 J1101 03 = S1.D J1401 01 = GTN
Parameter 2 = Resolution J1101 04 = S.P.D. J1105 00 = Pos
J0200 00 = 1 Parameter 10 = Units J1105 01 = Zer J1402 00 = Off
J0200 01 = 2 J1000 00 = Lb only J1102 00 = Pos J1402 01 = 1
J0200 02 = 5 J1000 01 = Kg only J1102 01 = Zer J1106 00 = Off J1402 02 = 2
J0200 03 = 10 J1000 02 = Lb/Kg Conversion J1106 01 = 1 J1402 03 = 3
J0200 04 = 20 J1103 00 = Off J1106 02 = 2 J1402 04 = 4
J0200 05 = 50 Parameter 11 - Setpoints J1103 01 = S2 J1106 03 = 3
J0200 06 = 100 J1100 00 = Off J1103 02 = S2.P J1106 04 = 4. J1403 00 = Off
J1100 01 = SP J1103 03 = S2.D J1106 05 = 5 J1403 01 = Co
Parameter 3 = Decimal Point J1101 00 = Off J1103 04 = S.P.D. J1106 06 = 6 J1403 02 = De
J0300 00 = 0 J1101 01 = S1 J1106 07 = 7
J0300 01 = 0.0 J1101 02 = S1.P J1104 00 = Pos J1106 08 = 8 J1404 00 = 3
J0300 02 = 0.00 J1101 03 = S1.D J1104 01 = Zer J1106 09 = 9 J1404 01 = 6
J0300 03 = 0.000 J1101 04 = S.P.D. J1106 10 = 10 J1404 02 = 12
J0300 04 = 0.0000 J1100 04 = Bat2 J1404 03 = 24
J1102 00 = Pos J1101 00 = Off Parameter 12 = Zero Band J1404 04 = 48
Parameter 5 = Digital Averaging J1102 01 = Zer J1101 01 = S1 J1200 00 = Off J1404 05 = 96
J0500 00 = 1 J1101 02 = S1.P J1200 01 = 1
J0500 01 = 2 J1103 00 = Off J1101 03 = S1.D J1200 02 = 2 J1405 00 = Off
J0500 02 = 4 J1103 01 = S2 J1101 04 = S.P.D. J1200 03 = 3 J1405 01 = Co
J0500 03 = 8 J1103 02 = S2.P J1200 04 = 4 J1405 02 = De
J0500 04 = 16 J1103 03 = S2.D J1102 00 = Pos J1200 05 = 5
J0500 05 = 32 J1103 04 = S.P.D. J1102 01 = Zer J1200 06 = 6 (J1406 for SI only)
J0500 06 = A1 J1103 05 = tol. J1200 07 = 7 J1406 00 = 3
J0500 07 = A2 J1103 00 = Off J1200 08 = 8 J1406 01 = 6
J1104 00 = Pos J1103 01 = 1 J1200 09 = 9 J1406 02 = 12
Parameter 6 = Tare J1104 01 = Zer J1103 02 = 2 J1200 10 = 10 J1406 03 = 24
J0600 00 = ATNR J1103 03 = 3 J1200 11 = 20 J1406 04 = 48
J0600 01 = Auto J1103 04 = 4. J1200 12 = 30 J1406 05 = 96
J0600 02 = FT J1103 05 = 5 J1200 13 = 40
Table 3-7. Configuration Setup Parameters