Rice Lake Sartorius Midrics 1 and 2 Series - Operating Instructions User Manual
Page 86
Classification Application
The “Initialization data" block contains
the upper limits of Classes 1 through 4.
The “Results" block contains gross, net
and tare weights, as well as the class
that the sample belongs to (1 through
5, where Class 5 means that the upper
limit of Class 4 was exceeded).
--------------------
Lim1
+
10.000 kg
Lim2
+
11.000 kg
Lim3
+
12.000 kg
Lim4
+
13.000 kg
G#
+
9.700 kg
T
+
0.000 kg
N
+
9.700 kg
Class
1
--------------------
Animal Weighing Application
The “Initialization data" block contains
the number of measured values that
averaging is based on. The “Results"
block contains the tare weight and the
mean value.
--------------------
mDef
8
T
+
0.000 kg
x-Net +
4.202 kg
--------------------
Net-total Formulation Application
The “Initialization data" block is blank.
If this block is enabled for the printout,
a blank line is output.
Which data is contained in the “Results"
block value depends on the program
operating status at the time of printing.
The following options are available:
– Total/results printout
After c is pressed (tare memory
is cleared)
– Individual/components printout
After O is pressed (component
is stored in tare memory)
– Standard
After p is pressed (component
is not stored in tare memory)
‘Total' printout:
--------------------
n
2
S-Comp+
3.200 kg
Cont.T+
0.200 kg
--------------------
Component printout (menu item
3.17.3
)
When the components printout is
configured, the header is printed only
once, followed by all components.
If you are using a label printer, make sure
a single label is large enough for the
list of all components. For printer models
YDP01IS and YDP04IS, you can configure
manual form feed in the operating menu.
If the corresponding setting is active,
you can activate “form feed" manually.
With the YDP02IS printer, form feed is
automatic after each print command
(fixed setting).
Example with 2 components
HEADER LINE 1
HEADER LINE 2
14.01.2006
09:43
--------------------
Cmp001+
1.200 kg
Cmp002+
2.000 kg
Individual printout (menu item
3.17.2
)
The entire standard printout is generated
for each component.
Example for the second component:
HEADER LINE 1
HEADER LINE 2
14.01.2006
09:46
--------------------
Cmp002+
2.000 kg
Standard printout
Example before the second component
is stored:
G#
+
3.400 kg
T
+
0.200 kg
T2
+
1.200 kg
N
+
2.000 kg
Totalizing Application
The “Initialization data" block is empty.
If this block is enabled for the printout,
a blank line is output.
Which data is contained in the “Results"
block value depends on the program
operating status at the time of printing.
The following options are available:
– Printout of results
After c is pressed (totalizing memory
is cleared)
– Individual/component printout
of one transaction
After O is pressed (component
is stored in tare memory)
– Standard printout
After p is pressed (component
is not stored in tare memory)
‘Total' printout:
--------------------
*G
9.200 kg
*N
+
8.600 kg
n
3
--------------------
Component printout
(menu item
3.17.3
)
The header is printed only once;
all transactions are printed one after
the other. For printing on a label
printer, see also “Component printout,
Net-total."
Example with 2 transactions:
HEADER LINE 1
HEADER LINE 2
14.01.2006
09:43
--------------------
G#
+
1.400 kg
T
+
0.200 kg
N
+
1.200 kg
n
1
G#
+
3.400 kg
T
+
0.200 kg
N
+
3.200 kg
n
2
86