Panasonic AG-DTL1P - Manual (Page 26)

Useful functions
Alarm memory recall and power
loss memory recall
Alarm memory recall is a function for storing in the
memory those dates/times and number of occasions
on which the alarm recording and sensor recording
functions were activated.
Power loss memory recall is a function for storing in
the memory those dates/times and number of
occasions on which the primary power supply was
shut off due to a power outage, etc.
J
Set the POWER switch to ON.
2
Set the PROGRAM switch to the MENU position
while holding down the STOP button.
The ALARM RECALL screen and POWER LOSS
MEMORY screen now appear.
The alarm number/s and dates/times when the
alarm signal was input are displayed on the
ALARM RECALL screen.
The number of times the primary power source has
been shut off and the dates/times when this
happened are displayed on the POWER LOSS
MEMORY screen.
(Data is displayed in sequence with the latest at
the top of the screen.)
[ALARM RECALL]
29 12 - 30 - 2000 3:15
28 12 - 04 - 2000 12:10
27 10 - 25 - 2000 2:20
26 9 - 10 - 2000 2:30
25 8 - 11 - 2000 6:55
24 5- 10-2000 3:22
23 4 - 11 - 2000 6:55
22 3- 10-2000 3:22
[POWER LOSS MEMORY]
14 12 - 01 -2000 12:00
13 10 - 05 - 2000 10:30
12 08- 10 - 2000 9:20
11 3-02-2000 7:00
The following display appears when alarm recording
was never performed or when the primary power
supply was never shut off.
[ALARM RECALL]
■ + + - 4 ; - f - 4=4;
4^ 4-—4 4—4 4 4 4
4; 4-—4 4—4 4 44
44—44—444 4
44—4 4—4 4 44
4 4:44
4 4:44
4 4:44
4 4:4 :f-
4 4:4 4
4^::41-
4 4:44
4 4:44
[POWER LOSS MEMORY]
44—44—4444 44:44
>f; rf: 44—44—44 44 4 4:4 4
44 4 4"—4 4—4 4 44 4 : 4 4
<Notes>
• Data for up to 8 alarms is stored on the ALARM
RECALL screen whereas data for up to 4 power
losses is stored on the POWER LOSS MEMORY
screen.
• A total of 99 alarms and 99 power tosses are stored
in the memory.
When 99 is exceeded, the count returns to “00.”
• As with alarm recordings, the sensor recordings are
stored as alarm memory data.
• The alarm memory data and power loss memory
data are stored in the memory circuit inside the unit.
They are not recorded on the tape.
• When the PROGRAM switch is set to any position
except MENU, the ALARM RECALL screen and
POWER LOSS MEMORY screen displays are
cleared.
• When the RESET button is pressed while the
ALARM RECALL screen is displayed, the memory
can be cleared, but the POWER LOSS MEMORY
screen is not cleared.
[ALARM RECALL]
44 44_44_4444 44:4 4
4 4 4 4—4 4—4 4 4 4
'f’^ ^ ^ ^ 44:44
44 44—44—4444
44 4>f:_4:ir_4444 4.-(^:4 4
44 44-44-4444 4 4;;(;4
[POWER LOSS MEMORY]
14 12-01-2000 12:00
13 10-05-2000 10:30
12 08-10 - 2000 9:20
11 3 - 02 - 2000 7:00
26