Genicom GEK 00031B - Manual (Page 312)

Index GEK-00029B 312
Forms sequence, start <DECIFM>.................... 167
Forms sequence, terminate <DECTFM>........... 171
Graphic size modification <GSM>.................... 175
Graphic size selection <GSS> ........................... 175
Graphics density, set <DECSGD> .................... 193
Horizontal pitch, set <DECSHORP> ................ 192
Horizontal position, absolute <HPA>................ 178
Horizontal position, backward <HPB>.............. 184
Horizontal position, relative <HPR> ................. 178
Horizontal spacing, select <SHS> ..................... 177
Horizontal tab stops, set <DECSHTS> ............. 191
Horizontal tab, set ............................................. 159
Index <IND> ..................................................... 158
Line feed / new line <LNM>............................. 181
Lines per physical page, set <DECSLPP> ........ 190
Load vertical format unit <VFU>...................... 182
Loading forms <DECLFM>.............................. 165
Loading Logo <DECLG>.................................. 169
Logo sequence, select........................................ 164
Margins, left and right, set <DECSLRM>......... 190
Margins, top and bottom, set <DECSTBM> ..... 189
Next line <NEL> ............................................... 158
Operating system command <OSC> ................. 161
Partial line down <PLD>................................... 159
Partial line up <PLU>........................................ 159
Pitch select mode <PSM> ................................. 182
Position unit mode <PUM>............................... 181
Privacy message <PM> ..................................... 161
Product identification <DA> ............................. 180
Proprinter emulation mode <DECIPEM> ......... 161
Request font status <DECRFS> ........................ 163
Request logo status <DECRLGS>..................... 162
Reset mode <RM> ............................................ 184
Reset to initial state <RIS>................................ 179
Reverse index <RI>........................................... 160
Select graphics rendition <SGR> ...................... 162
Select other coding system (Epson) <SOCS> ... 173
Select other coding system (Proprinter) <SOCS>
...................................................................... 174
Set mode <SM>................................................. 181
Single shift 2 <SS2>.......................................... 160
Single shift 3 <SS3>.......................................... 160
Sixel graphics .................................................... 168
Soft terminal reset <DECSTR>......................... 187
String terminator <ST> ..................................... 160
Tab clear <TBC>............................................... 181
Vertical pitch, set <DECVERP> ....................... 192
Vertical position, absolute <VPA>.................... 180
Vertical position, backward <VPB>.................. 184
Vertical position, relative <VPR> ..................... 180
Vertical spacing, select <SVS> ......................... 177
Vertical tab stops, set <DECSVTS>.................. 191
Vertical tab, set.................................................. 159
Control codes ......................................................... 155
<BEL> Bell ....................................................... 155
<BS> Backspace ............................................... 155
<CAN> Cancel .................................................. 157
<CR> Carriage return........................................ 156
<DC1> Device Control 1 .................................. 156
<DC3> Device Control 3 .................................. 157
<ESC> Escape................................................... 157
<FF> Form feed ................................................ 156
<SI> Shift in ......................................................156
<SO> Shift out...................................................156
<SUB> Substitute ..............................................157
<VT> Vertical tab..............................................156
line terminators.............................................................10
O
operating system command (OSC) .................................9
P
PPL 3 ..........................................................................195
7-bit Versus 8-bit environments .............................196
C1 control characters..............................................201
Coded characters ....................................................195
Command Directory...............................................207
Commands
Announce subset of code extension facilities
<ASCEF> ......................................................209
Autowrap Mode <DECAWM>..........................214
C1 Transmit / Receive <SnC1R/DEC*C1> .......245
Carriage Return / New Line Mode <DECCRNLM>
.......................................................................215
Clear All Horizontal Tabs <DECCAHT>..........214
Clear All Vertical Tabs <DECCAVT> ..............215
Control representation mode <CRM>................210
Cursor position report <CPR> ...........................209
Cursor up <CUU>..............................................210
Device Status Report .........................................230
Device Status Request <DSR> ..........................229
Draw Relative Vector <DECRVEC> ................218
Draw Vector <DECVEC> .................................227
Entering IBM Proprinter Emulation Mode
<DECIPEM>.................................................216
Graphic Size Modification <GSM>...................231
Graphic Size Selection <GSS> ..........................232
Graphics, carriage return <DECGCR> ..............258
Graphics, next line <DECGNL>........................258
Graphics, raster attributes, set <DECGRA> ......259
Graphics, repeat introducer <DECGRI>............260
Horizontal Position Absolute <HPA>................233
Horizontal Position Backward <HPB> ..............234
Horizontal Position Relative <HPR>.................235
Horizontal Tab Set <DECHTS> ........................215
Line Feed / New Line Mode <LNM> ................236
Locking and Single Shifts..................................236
New Sheet <DECNS> .......................................216
Pitch Select Mode <DECPSM>.........................216
Positioning Unit Mode <PUM>.........................237
Printer attributes <DA> .....................................210
Printer attributes report <DAR> ........................211
Proportional Spacing Mode <DECPSP> ...........217
Request Font Status <DECRFS> .......................217
Reset to Initial State...........................................237
Secondary printer attributes <DA2> ..................212
Select Character Set <SCS>...............................238
Select Graphics Rendition <SGR> ....................240
Select Size Unit <SSU>.....................................247