Genicom GEK 00031B - Manual (Page 313)

GEK-00029B 5000 Series Programmer’s Manual 313
Set Horizontal Pitch <DECSHORP>................. 219
Set Horizontal Spacing <SHS> ......................... 244
Set Horizontal Tab Stops <DECSHTS>............ 220
Set Left and Right Margins <DECSLRM> ....... 222
Set Lines per Physical Page <DECSLPP> ........ 221
Set Top and Bottom Margins <DECSTBM>..... 223
Set Vertical Pitch <DECVERP> ....................... 228
Set Vertical Spacing <SVS>.............................. 248
Set Vertical Tab Stops <DECSVTS> ................ 226
Soft Terminal Reset <DECSTR> ...................... 225
Spacing Pitch Increment <SPI>......................... 246
Tab Clear <TBC> .............................................. 249
Vertical Position Absolute <VPA> ................... 249
Vertical Position Backward <VPB>.................. 250
Vertical Position Relative <VPR>..................... 250
Vertical Tab Set <DECVTS> ............................ 229
Control characters
<CSI> Control sequence introducer .................. 201
<DCS> Printer control string............................. 201
<EPA> End of protected area............................ 201
<ESA> End of selected area .............................. 201
<HTS> Horizontal tab set.................................. 202
<IND> Index ..................................................... 202
<NEL> Next line ............................................... 202
<PLD> Partial line down................................... 202
<PLU> Partial line up........................................ 202
<RI> Reverse index........................................... 202
<SS2> Single shift 2.......................................... 202
<SS3> Single shift 3.......................................... 202
<ST> String terminator...................................... 202
<VTS> Vertical tab set...................................... 202
Control codes ......................................................... 199
<BEL> Bell ....................................................... 199
<BS> Backspace................................................ 199
<CAN> Cancel .................................................. 199
<CR> Carriage return ........................................ 199
<ESC> Escape................................................... 199
<FF> Form feed................................................. 199
<HT> Horizontal tab ......................................... 200
<LF> Line feed.................................................. 200
<SI> Shift in ...................................................... 200
<SO> Shift out .................................................. 200
<SUB> Substitute.............................................. 200
<VT> Vertical tab ............................................. 200
Horizontal advance increments .............................. 254
Page coordinate system.......................................... 251
Character cell model.......................................... 252
Origin and extent ............................................... 252
Point model ....................................................... 252
Positioning and movement ................................ 253
Printable characters................................................ 198
Sixes graphics ........................................................ 256
printer emulation ............................................................ 8
Printronix 300/600 ....................................................... 66
Printronix P300/600
Control Codes .......................................................... 66
<ACK> Line at 8lpi............................................. 66
<BS> Elongated Character Line.......................... 66
<CR> Carriage Return Slew Zero or Edit Mode . 66
<DC1> Ready/Select ........................................... 66
<DC3> Busy/Select ............................................. 67
<DLE> High vertical density graphics ................ 67
<ENQ> Normal density plot line .........................67
<EOT> High density plot line..............................67
<ETX> End of transmission ................................67
<FF> Form Feed ..................................................67
<HT> Horizontal Tab ..........................................67
<LF> Line Feed ...................................................67
<RS> Record Separator .......................................67
<SI> Shift In ........................................................68
<SO> Shift Out ....................................................68
<SP> Space..........................................................68
<UNDL> Underline.............................................68
<US> Unit Separator ...........................................68
<VT> Vertical Tab...............................................68
Bell code <BEL> .................................................66
Control Codes<DEL> Delete ...................................67
Electronic Vertical Format Unit ...............................72
Graphics ...................................................................69
Dot Patterns .........................................................70
Dot Patterns and Densities ...................................69
Printronix P300/600 Emulation Options Table...........274
Printronix Pseries Emulation Options Table...............274
Proprinter
Command Directory ...............................................111
Commands
<HT> Horizontal Tab ........................................110
Automatic line feed............................................114
Deselect printer ..................................................117
Double strike print, start ....................................115
Double wide print, on/off...................................118
Emphasized print, start.......................................115
Emphasized print, stop.......................................115
Form length in inches, set ..................................115
Graphics, high-speed double density, set ...........120
Graphics, low speed double density, set.............120
Graphics, quadruple density, set ........................121
Graphics, set normal density ..............................120
Horizontal margins, set ......................................118
Horizontal tab stops, set .....................................115
Overscore ...........................................................112
Print continuously from all character chart ........112
Print mode, select...............................................116
Print single character from all character chart....112
Proportional spacing, set ....................................117
Select character set 1..........................................114
Select character set 2..........................................114
Select code page.................................................113
Set 12 cpi ...........................................................112
Set 7/72 line spacing ..........................................113
Set 8 lpi ..............................................................113
Set form length in lines ......................................115
Set graphics line spacing....................................114
Set top of form ...................................................114
Skip perforation, cancel .....................................116
Skip perforation, set ...........................................116
Start text line spacing.........................................113
Store 7/72 line spacing.......................................114
Superscript / Subscript, reset..............................117
Superscript / Subscript, Set ................................117
Tabs, power on settings, set all ..........................117
Underscore.........................................................112
Unidirectional printing, set ................................117
Variable line feed...............................................116