Panasonic AJ-HPX2000 - Manual (Page 149)

149 Maintenance and Inspections : Warning System
M
a
in
te
nan
ce an
d Insp
ecti
on
s
Card Warning Code
Code No. Description Recording
Indication in display
window
E-70
The directory organization on the inserted P2
card does not comply with the standards. ([DIR
NG CARD (Slot No.)] is indicated on the
viewfinder.) Although different kinds of recording
operations will function, data may not be
recorded properly. Use the unit to format the
card immediately.
A warning code blinks once
every 2 seconds on the time
code display section of the
display window.
E-71
A P2 card was inserted where the number of
rewrites exceeds the limit of the standards.
([RUN DOWN CARD (Slot No.)] is indicated on
the viewfinder.) Although different kinds of recording
operations will function, data may not be
recorded properly. It is recommended to
replace it.
Warning and Error Display for Thumbnail Operation and USB HOST MODE
Item Message Description Measure
Thumbnails
CANNOT ACCESS! Data cannot be accessed because it is
corrupted or for other reasons. Restore media and clips to normal state before
access.
WRITE
PROTECTED! The P2 or SD card is write protected. Insert write-enabled media.
CARD FULL! The P2 or SD card is full. Insert media with sufficient capacity.
NO CARD! No P2 or SD card is inserted. Insert compatible media.
NO FILE! The designated file is not found. Check the file.
CANNOT COPY! Images cannot be copied. Check the conditions for copying.
CANNOT DELETE ! Contents version mismatch prevents
deletion. Match devices and contents version.
UNKNOWN
CONTENTS
FORMAT! Warning displayed to indicate contents
version mismatch. Match devices and contents version.
CANNOT FORMAT! P2 card problem prevents formatting. Check P2 card.
CANNOT REPAIR! Data cannot be repaired since content that
cannot be repaired is selected. Check selected content.
CANNOT RE-
CONNECT! A clip that does not span multiple P2 cards
cannot be reconnected. Check selected content.
INVALID VALUE! Entered data was invalid. Enter data in a valid range.
UNKNOWN DATA! The metadata character code is invalid. Use UTF-8 for the metadata character code. Use
the viewer to enter correct characters.
CANNOT REPAIR IN
SELECTION! Some of the selected clip could not be
repaired.
NO SD CARD! No SD card is inserted. Insert an SD card.
NO COPY TO SAME
CARD! A clip cannot be copied to the card storing
the original clip. Copy the selected clip to a card that does not
contain the original clip.
SAME CLIP IS
SELECTED! The clip cannot be copied because a clip that
has already been copied and the original clip
have been selected. Confirm the selected clip and release either the
source clip or the destination clip and then execute
the copy operation.
USER CLIP NAME
MODIFIED! Characters in the clip name had to be
deleted in adding the counter value. The user clip name plus the counter value can only
contain up to 100 bytes. Characters in the clip
name are automatically deleted when the total
exceeds 100 bytes.
TOO MANY CLIPS! Too many clips are selected. Reduce the number of selected clips.
LACK OF REC
CAPACITY! There is not enough recording capacity left
on the card. Insert a card with sufficient recording capacity.
CANNOT CHANGE! Any thumbnails that cannot be produced on
the AVC-Intra 100 or AVC-Intra 50 and
displayed in gray cannot be changed at the
text memo position. Install the AVC-Intra codec board (AJ-YBX200G,
optional) and set SYSTEM MODE according to the
clips.
MISSING CLIP! A shot mark will be added to the clips recorded
on multiple P2 cards when all P2 cards are not
inserted yet. Insert all P2 cards with recorded clips, and confirm
that the
incomplete clip indicators disappear, and
then add shot marks.
AJ-HPX2000P(VQT1D27-1)E.book 149 ページ ２００７年７月３０日 月曜日 午後１時３１分