Panasonic AJ-HPX2000 - Manual (Page 73)

73 Adjustments and Settings for Recording : Viewfinder Screen Status Displays
A
d
ju
stm
ents and S
e
tti
ngs f
o
r
Rec
o
rdi
n
g
Information Item Indication Status
11. Camera Warning and
Report Area
(related to AWB, ABB
and switch settings)
AWB A ACTIVE
AWB B ACTIVE
AWB A OK
¢.¢K
AWB B OK ¢.¢K
AWB BREAK ¢.¢K
AWB NG
COLOR TEMP LOW
COLOR TEMP HIGH
LEVEL OVER
LOW LIGHT
TIME OVER
ATW MODE
AWB PRESET ¢.¢K
CHECK FILTER
ABB ACTIVE
ABB OK
ABB BREAK
ABB NG
B-SHD READY
B-SHD ACTIVE
B-SHD OK
B-SHD BREAK
B-SHD NG
AWB being performed on Ch A.
AWB being performed on Ch B.
AWB successful on Ch A.
AWB successful on Ch B.
AWB action aborted by user.
AWB action failed. The second line indicates the status.
Color temperature too low.
Color temperature too high.
Brightness too high.
Brightness too low.
Action timed-out.
This is indicated when AWB cannot be executed since ATW is being
operated.
AWB cannot be performed because the AWB switch is position at PRE or
the super gain is enabled.
Make sure the FILTER control is positioned correctly.
ABB being performed.
ABB action successful.
ABB action aborted by user.
ABB action failed.
Black shading accepted (by holding down the ABB switch during ABB
adjustment).
Black shading being adjusted.
Black shading adjustment successful.
Black shading adjustment aborted by user.
Black shading adjustment failed.
(Switch changeover
indication) WHITE: # ¢.¢K
AUTO KNEE: ON/OFF
GAIN:
¢¢dB
SS: 1/ ¢¢¢¢
SS: 1 1/¢¢¢¢
FILTER: ¢ ¢.¢K
EXTENDER: ON/OFF
IRIS:
¢¢ F ¢.¢
The WHITE BAL switch has been switched. # is replaced with A, B or PRST.
When [A] and [B] are set to “VAR”, then it is indicated as VAR
¢.¢ K. When
[B] is assigned ATW, then it is indicated as ATW MODE.
AUTO KNEE switch has been switched to ON or OFF.
Gain has been switched with the GAIN selector switch or a user button.
When the shutter speed has been switched, the shutter speed is indicated.
Shutter speed is in SYNCRO SCAN mode.
Filter position and detail have been switched.
Lens extender has been turned on or off.
Indicated when the iris override correction value is to be changed.
(Low light warning) LOW LIGHT Brightness too low.
(Y GET value) ¢¢¢.¢% With the Y GET ON setting, the output brightness level near the center
marker is displayed as “%.”
(MARKER indication) MKR: A/B/OFF Current marker type
12. User button
functions
UM: USER MAIN
button
U1: USER1 button
U2: USER2 button
INH
S.GAIN
¢¢dB/OFF
DS.GAIN ¢¢ :/OFF
LINE MIX ON/OFF
S.IRIS ON/OFF
I.OVR ON/OFF
S.BLK –
¢¢/OFF
B.GAMMA ON/OFF
AUDIO CH1
AUDIO CH2
REC SW
Y GET ON
RET SW
ATW ON/OFF
D.ZOOM
a2/a3/a4/OFF
SLOT SEL
PRE REC
USB HOST/DEVICE/OFF
DRS ON/OFF
ASSIST ON/OFF
C.TEMP
User buttons disabled.
Selected S.GAIN
Selected DS.GAIN
Whether LINE MIX GAIN is ON or OFF.
Whether S.IRIS is ON or OFF.
Iris override can be set (the IRIS OVERRIDE setting is ON).
Status of SUPER BLACK (ON or OFF). When it is ON, the set value is also
indicated.
Status of BLACK GAMMA (shade correction for the black level): ON or OFF
Input signal to be recorded on Audio Channel 1 has been switched.
Input signal to be recorded on Audio Channel 2 has been switched.
USER button acts as REC switch.
Y GET function ON.
USER button acts as RET switch.
ATW being performed.
Magnification of digital zoom
Switch that changes the target card is set.
Indicates that PRE RECORDING mode has been switched ON or OFF.
USB action status has been switched.
Indicates whether the dynamic range stretcher function is ON or OFF.
Indicates whether the focus assist function is ON or OFF.
Indicates the mode for changing the color temperature with the JOG dial
button is ON or OFF.
AJ-HPX2000P(VQT1D27-1)E.book 73 ページ ２００７年７月３０日 月曜日 午後１時３１分