Toshiba Tosvert VF-AS1 - Manual (Page 253)

K-15
E6581301
11
[16] PID control [2/2]
Vector control
Title
Communi
cation
No.
Function Adjustment range
Minimum
setting unit
(Panel/Communi
cation)
Default
setting
Write during
running
Speed
control
Torque
control
PM
control
V/f Reference
H 0363 Integral (I) gain 0.01~100.0 0.01/0.01 0.10 Enabled ●/● - ● ● *1
H 0364 PID deviation upper limit NN ~WN Hz 0.1/0.01 *2 Enabled ●/● - ● ● *1
H 0365 PID deviation lower limit NN ~WN Hz 0.1/0.01 *2 Enabled ●/● - ● ● *1
H 0366 Differential (D) gain 0.00~2.55 0.01/0.01 0.00 Enabled ●/● - ● ● *1
*1: ⇒ For details, refer to Instruction Manual (E6581329) specified in Section 6.41. *2: Inverter with a model number ending with -WN: 60.0 -WP: 50.0
[17] Speed feedback/positioning control
Vector control
Title
Communi
cation
No.
Function Adjustment range
Minimum
setting unit
(Panel/Communi
cation)
Default
setting
Write during
running Speed
control
Torque
control
PM
control
V/f Reference
H 0367 Process upper limit NN ~WN Hz 0.1/0.01 *4 Enabled -/● -/● - - *1
H 0368 Process lower limit NN ~WN Hz 0.1/0.01 NN Enabled -/● -/● - - *1
H 0369 PID control waiting time 0~2400 sec. 1/1 0 Enabled -/● -/● - - *1
H 0370 PID output upper limit NN ~WN Hz 0.1/0.01 *4 Enabled - - - - *1
H 0371 PID output lower limit NN ~WN Hz 0.1/0.01 NN Enabled - - - - *1
H 0372
Process increasing rate (speed type
PID control)
0.1~600.0 0.1/0.1 10.0 Enabled - - - - *1
H 0373
Process decreasing rate (speed
type PID control)
0.1~600.0 0.1/0.1 10.0 Enabled - - - - *1
H 0375 Number of PG input pulses 12~9999 1/1 500 Disabled ●/● -/● - - *2
H 0376
Selection of number of PG input
phases
1:Single-phase input
2:Two-phase input
1/1 2 Disabled ●/● - - - *2
H 0377 PG disconnection detection
0:Deselect
1:Select (with filter)
2:Select (Detection of momentary power failure)
1/1 0 Disabled ●/● - - - *2
H 0378
Number of RP terminal input
pulses
12~9999 1/1 500 Disabled ●/● ●/● - - *3
H 0381
Simple positioning completion
range
1~4000 1/1 100 Enabled ●/● - ● ● *2
*1: ⇒ For details, refer to Instruction Manual (E6581329) specified in Section 6.41. *2: ⇒ For details, refer to Instruction Manual (E6581319) specified in Section 6.41.
*3: ⇒ For details, refer to Instruction Manual (E6581341) specified in Section 6.41. *4: Inverter with a model number ending with -WN: 60.0 -WP: 50.0
[18] Motor constant [1/2]
Vector control
Title
Communi
cation
No.
Function Adjustment range
Minimum
setting unit
(Panel/Communi
cation)
Default
setting
Write during
running
Speed
control
Torque
control
PM
control V/f Constant Reference
H 0400 Auto-tuning 1
0:No auto-tuning
1:Initialize motor constant (0 after execution)
2:Continue operation continued after auto-tuning (0
after execution)
3:Auto-tuning by input terminal signal
4:Motor constant auto calculation (0 after
execution)
1/1 0 Disabled ●/● ●/● - - 6. 22
Sensorless vector/vector with sensor (●:Effective, -:Ineffective)
Sensorless vector/vector with sensor (●:Effective, -:Ineffective)
Sensorless vector/vector with sensor (●:Effective, -:Ineffective)