Alpha Technologies XM2-300CE-HP - Manual (Page 42)

4.0 Operation, continued
4.3
Smart Display modes for XM2-300HP, continued
4.3.4 Menu Structure and Navigation (from Operation Normal screen)
COMMS INFO
Float V/C = 2.27 V
TEST: 10 MIN
37.3 V
+
<ESC>
+
OPERATION NORMAL
SETUP MENU
CODE VER = 7.01.0
DEVICE ADDRESS= 1
ALPHACELL = OTHER
FLOAT V/C=2.27
ACCEPT V/C=2.40
TEMP COMP=5mV
BATT CAPACITY=100Ah
# BATT STRINGS*
BATT 1 DATE M/Y
BATT 2 DATE M/Y**
BATT 1 MHOS
BATT 2 MHOS**
MHO 1 DATE M/Y
MHO 2 DATE M/Y***
BATTERY 1 LIFE
BATTERY 1 AGE
BATTERY 2 LIFE**
BATTERY 2 AGE**
MHO’S MIN LEVEL
MHO’S MAJ LVL
STANDBY TIME=65M
STANDBY EVENTS=12
TOTAL RUN TIME = 365D
SELF TEST = OFF
TEST INTERVAL
TEST INHIBIT.
%DISCHARGE
TEST DURATION = 10M
TEST COUNTDOWN
FREQ RANGE = 3.0Hz
PIM OPTION = YES
RESET OUT 1
RESET OUT 2
OVER CURR 1 = 15.0A
OVER CURR 2 = 15.0A
RETRY DLY = 60s
RETRY LMT
OVER CURR TOL = 3000
SYSTEM FAN*
HEATER MAT*
PS PRIORITY*
TECHNICIAN ID*
INPUT LIMIT*
SET DEFAULTS
SELECT LANGUAGE
(Auto-Scroll Information)
OPER MODE = LINE
BATT STATUS
INV STATUS
DPM STATUS
INPUT VOLTAGE 120V
INPUT CURRENT
INPUT WATTS
OUTPUT VOLTAGE 89V
OUTPUT 1 CURR
OUTPUT 2 CURR
CHARGER MODE = FLOAT
BATT VOLTAGE 40.5V
BATTERY TEMP 37°C
ENCLOSURE TEMP
CHARGER CURRENT 8.2A
EST. BATT RUN
12 EVENTS 65 MIN
To Single-step
Back to Auto-Scroll
Back to
Auto-Scroll
OPER MODE = LINE
BATT STATUS
INV STATUS
DPM STATUS
INPUT VOLTAGE 120V
INPUT FREQUENCY 60Hz*
INPUT CURRENT
INPUT WATTS
OUTPUT VOLTAGE 89V
OUTPUT 1 CURR
OUTPUT 2 CURR
OUTPUT WATTS
OUTPUT VA 1060*
PERCENT LOAD 80%
CHARGER MODE = FLOAT
BATT VOLTAGE 40.5V
BATTERY TEMP 37°C
ENCLOSURE TEMP
CHARGER CURRENT 8.2A
EST. BATT RUN
12 EVENTS 65 MIN
*Only visible when in single-step mode
To Self-test
Self-test OFF
Back to Operation Normal
To COMMS INFO
Back to Operation Normal
COMMS INFO
(Single-step Information)
To Single-step
(Single-step Information)
SETUP MENU
(Single-step information)
(Auto-Scroll Information)
Operation Normal
Back Auto-Scroll
To
Program Mode
Selection returns to
Single-Step
Set-Up Menu
To Accept New Data
To Accept New Data
To Abort
Edit using
LEGEND
Control
Panel
Key
Display
Symbol
Description
UP Arrow
DOWN Arrow
ESCAPE
ENTER
BATT.SPANNUNG
(Auto-Scroll Information)
To Single-step
Back to Auto-Scroll
Back to Single-step
Setup Menu
LANGUAGE =
ENGLISH
SPANISH
FRENCH
GERMAN
CM = 00:90:EA:12:34:56
CPE = 00:90:EA:12:34:57*
CM = 192.168.123.123
CPE = 192.168.123.124*
CM Rx PWR = -12.9 dBmV
CM Tx PWR = 34.5 dBmV
DN FREQ = 300.000 MHz
UP FREQ = 15.000 MHz
MODEL = DPM
SW = xx.xx.xx.xx
CM = 00:90:EA:12:34:56
CPE = 00:90:EA:12:34:57*
CM = 192.168.123.123
CPE = 192.168.123.124*
CM Rx PWR = -12.9 dBmV
CM Tx PWR = 34.5 dBmV
DN FREQ = 300.000 MHz
UP FREQ = 15.000 MHz
MODEL = DPM
SW = xx.xx.xx.xx
* only shown in
Dual-IP configurations
220GOLD
220HPL-FT
220GXL
210GXL
195GXL
195GOLD
180GXL
165GXL
115HPL-FT
85GXL
70HPL-FT
CODEVER = 7.01.0
DEVICE ADDRESS = 1
ALPHACELL=OTHER
FLOAT V/C = 2.27
ACCEPT V/C = 2.40
TEMP COMP=5mV
BATT CAPACITY = 100Ah
BATTERY1 DATE
BATTERY1 MHOS
MHO1 DATA
BATTERY1 LIFE
BATTERY1 AGE
MHO’s MIN LVL
MHO’s MAJ LVL
STANDBY TIME=65M
STANDBY EVENTS=12
TOTAL RUN TIME=365D
SELF TEST = OFF
TEST INTERVAL
TEST INHIBIT
% DISCHARGE
TEST DURATION = 10M
TEST COUNTDOWN
FREQ RANGE = 3.0Hz
PIM OPTION = YES
RESET OUT 1
RESET OUT 2
OVERCURRENT1 = 15.0A
OVERCURRENT2 = 15.0A
RETRY DELAY = 60S
RETRY LIMIT = 20
OVERCURRENT TOL = 3000
SYSTEM FAN
HEATER MAT
PS PRIORITY
TECH ID
INPUT I LIMIT
SET DEFAULTS = NO
SELECT LANGUAGE
Pressing ENTER enables
the user to select the AlphaCell
battery in the system.
Values for Float, Accept,
Temp Comp and Battery
Capacity are automatically
selected.
**Visible when “Number of Battery
Strings” is set to 2.
*Visible in Single-step
To Setup Menu
42 017-877-B1-001 Rev. A