Alpha Technologies XM2-300CE-HP - Manual (Page 43)

4.0 Operation, continued
4.3
Smart Display modes for XM2-300HP, continued
4.3.5 Menu Structure and Navigation (from Active Alarms screen)
Auto-Scroll Information
To Operation Normal
(Auto-scroll Information)
OPERATION NORMAL OPERATION NORMAL
(Single-step Information)
Back to
Auto-Scroll
<ESC>
LEGEND
Description
SETUP MENU
(Auto-scroll Information)
Back to
Auto-scroll
To
Single-step
Sample Active
Alarm
To Single-step
Help Screens
Back to Auto-Scroll
To Single-step
To Active Alarms
***ACTIVE ALARMS***
(Auto-scroll Information)
Self Test Fail
Low Batt Volts
High Batt Volts
No Batteries
Batt Temp Probe
Line Isolation
Output Failure
Output Overload
Output 1 Tripped
Output 2 Tripped
Charger Failure
Input Failure
Inv Disconnected
Inverter Temp
Tap Fuse Fail
Config Error
N+1 In Use
N+1 Fault
***ACTIVE ALARMS***
Single-step Information
Output Overload
Single-step Information
1. Output Short Ckt?
2. Too Much Load
3. Chk Output Current
COMMS INFO
Float V/C = 2.27 V
SETUP MENU
CODE VER = 7.01.0
DEVICE ADDRESS= 1
ALPHACELL = OTHER
FLOAT V/C=2.27
ACCEPT V/C=2.40
TEMP COMP=5mV
BATT CAPACITY=100Ah
# BATT STRINGS*
BATT 1 DATE M/Y
BATT 2 DATE M/Y**
BATT 1 MHOS
BATT 2 MHOS**
MHO 1 DATE M/Y
MHO 2 DATE M/Y**
BATTERY 1 LIFE
BATTERY 1 AGE
BATTERY 2 LIFE**
BATTERY 2 AGE**
MHO’S MIN LEVEL
MHO’S MAJ LVL
STANDBY TIME=65M
STANDBY EVENTS=12
TOTAL RUN TIME = 365D
SELF TEST = OFF
TEST INTERVAL
TEST INHIBIT
%DISCHARGE
TEST DURATION = 10M
TEST COUNTDOWN
FREQ RANGE = 3.0Hz
PIM OPTION = YES
RESET OUT 1
RESET OUT 2
OVER CURR 1 = 15.0A
OVER CURR 2 = 15.0A
RETRY DLY = 60s
RETRY LMT
OVER CURR TOL = 3000
SYSTEM FAN*
HEATER MAT*
PS PRIORITY*
TECHNICIAN ID*
INPUT LIMIT*
SET DEFAULTS
SELECT LANGUAGE
OPER MODE = LINE
BATT STATUS
INV STATUS
DPM STATUS
INPUT VOLTAGE 120V
INPUT FREQUENCY 60Hz*
INPUT CURRENT
INPUT WATTS
OUTPUT VOLTAGE 89V
OUTPUT 1 CURR
OUTPUT 2 CURR
OUTPUT WATTS
OUTPUT VA 1060*
PERCENT LOAD 80%
CHARGER MODE = FLOAT
BATT VOLTAGE 40.5V
BATTERY TEMP 37°C
ENCLOSURE TEMP
CHARGER CURRENT 8.2A
EST. BATT RUN
12 EVENTS 65 MIN
COMMS INFO
(Single-step Information)
To Single-step
(Single-step Information)
(Auto-scroll Information)
Back Auto-scroll
To
Program Mode
To Accept New Data
To Accept New Data
To Abort
Edit using
Control
Panel
Key
Display
Symbol
UP Arrow
DOWN Arrow
ESCAPE
ENTER
Back to Single-step
Setup Menu
Output Overload
Auto-scroll Information
1. Output Short Ckt?
2. Too Much Load
3. Chk Output Current
Sample Active
Alarm
Back to Auto-scroll
Help Screens
To Help screens
for selected alarm
Self Test Fail
Low Batt Volts
High Batt Volts
No Batteries
Batt Temp Probe
Line Isolation
Output Failure
Output Overload
Output 1 Tripped
Output 2 Tripped
Charger Failure
Input Failure
Inv Disconnected
Inverter Temp
Tap Fuse Fail
Config Error
N+1 In Use
N+1 Fault
OPER MODE = LINE
BATT STATUS
INV STATUS
DPM STATUS
INPUT VOLTAGE 120V
INPUT CURRENT
INPUT WATTS
OUTPUT VOLTAGE 89V
OUTPUT 1 CURR
OUTPUT 2 CURR
OUTPUT WATTS
PERCENT LOAD 80%
CHARGER MODE = FLOAT
BATT VOLTAGE 40.5V
BATTERY TEMP 37°C
ENCLOSURE TEMP
CHARGER CURRENT 8.2A
EST. BATT RUN
12 EVENTS 65 MIN
CM 00:90:EA:12:34:56
CPE 00:90:EA:12:34:57*
CM 192.168.123.123
CPE 192.168.123.124*
CM Rx PWR -12.9 dBmV
CM Tx PWR 34.5 dBmV
DN FREQ 300.000 MHz
UP FREQ 15.000 MHz
MODEL DPM
SW xx.xx.xx.xx
*Only visible when in
single-step mode
Back to
Auto-scroll
To
Single-step
To Setup Menu
Back to
COMMS Info
To
COMMS Info
Back to
Operation Normal
CM 00:90:EA:12:34:56
CPE 00:90:EA:12:34:57*
CM 192.168.123.123
CPE 192.168.123.124*
CM Rx PWR -12.9 dBmV
CM Tx PWR 34.5 dBmV
DN FREQ 300.000 MHz
UP FREQ 15.000 MHz
MODEL DPM
SW xx.xx.xx.xx
* only shown in
Dual-IP configurations
Pressing ENTER enables
the user to select the AlphaCell
battery in the system.
Values for Float, Accept,
Temp Comp and Battery
Capacity are automatically
selected.
220GOLD
220HPL-FT
220GXL
210GXL
195GXL
195GOLD
180GXL
165GXL
115HPL-FT
85GXL
70HPL-FT
CODEVER = 7.01.0
DEVICE ADDRESS = 1
ALPHACELL=OTHER
FLOAT V/C = 2.27
ACCEPT V/C = 2.40
TEMP COMP=5mV
BATT CAPACITY = 100Ah
BATTERY1 DATE
BATTERY1 MHOS
MHO1 DATA
BATTERY1 LIFE
BATTERY1 AGE
MHO’s MIN LVL
MHO’s MAJ LVL
STANDBY TIME=65M
STANDBY EVENTS=12
TOTAL RUN TIME=365D
SELF TEST = OFF
TEST INTERVAL
TEST INHIBIT
% DISCHARGE
TEST DURATION = 10M
TEST COUNTDOWN
FREQ RANGE = 3.0Hz
PIM OPTION = YES
RESET OUT 1
RESET OUT 2
OVERCURRENT1 = 15.0A
OVERCURRENT2 = 15.0A
RETRY DELAY = 60S
RETRY LIMIT = 20
OVERCURRENT TOL = 3000
SYSTEM FAN
HEATER MAT
PS PRIORITY
TECH ID
INPUT I LIMIT
SET DEFAULTS = NO
SELECT LANGUAGE
Selection returns to
Single-Step
Set-Up Menu
LANGUAGE =
ENGLISH
SPANISH
FRENCH
GERMAN
**Visible when “Number of Battery
Strings” is set to 2.
*Visible in Single-step
43 017-877-B1-001 Rev. A