FEC DSP1500 (SAN3) - Manual (Page 75)

PAGE ６－13
enFORCE Operation Manual
Item
Parameter
Number
PARM
Data
Number D-
No
DATA
００ ００ Load unit number ０ :ＫＮ <No change>
００ ０１ ＳＰ version／copy between parameter <No change>
００ ０２ Amplifier Version <No change>
００ ０３ Function Version <No change>
００ ０４ Off Set Load ［KN］
００ ０５ Full Scale Extended Length ［mm］
００ ０６ Free Run Current Limit 0～1023
００ ０７ Home Position Off Set ［mm］
００ ０８ Near Origin Sensor Availability／Bank Change Enable
００ ０９ Home position search time out 0.1[sec] unit
００ ０Ａ Distance Decimal ０: NONE，１:0.1，２:0.01
００ ０Ｂ Free Run Distance Limit／Load Transducer Availability
００ ０Ｃ Current Load Conversion Ratio [%]
００ ０Ｄ Stroke Distance Limit／Recovery Time Decimal Point
００ ０Ｅ MANUAL Speed ［mm/sec］
System
００ ０Ｆ Option／Speed Decimal Point
００ １０ Tool Number
００ １１ Tool CAL Load ［KN］
００ １２ Tool CAL Voltage [Ｖ]
Tool
Data
００ １３ Tool Zero Load Voltage [Ｖ]
<No change> ００ １４～１Ａ In Home Control Data
Tool Type ００ ２０ Tool Number
０１～３２ ００ Operation Mode (Operation Method+Operation Step+Operation Finish Mode)
０１～３２ １０ Full-Scale Load ［KN］
０１～３２ １１ Minimum Load Value ［KN］
０１～３２ １２ Maximum Load Value ［KN］
０１～３２ １３ Standard Load ［KN］
０１～３２ １４ Speed Change Load ［KN］
０１～３２ １５ 1 ST Load ［KN］
０１～３２ １６ ＳＮＵＧ Load [KN］
０１～３２ １７ THRESHOLD Load ［KN］
Load
０１～３２ １８ CROS Load ［KN］
０１～３２ ２０ Minimum Distance Value ［mm］
０１～３２ ２１ Maximum Distance Value ［mm］
０１～３２ ２２ Standard Distance ［mm］
０１～３２ ２３ 1ST Distance ［mm］
Distance
０１～３２ ２４ CROS Distance ［mm］
０１～３２ ３０ Minimum Rate 1 [KN/mm]
０１～３２ ３１ Maximum Rate 1 [KN/mm]
０１～３２ ３２ Minimum Rate 2 [KN/mm]
Rate
０１～３２ ３３ Maximum Rate 2 [KN/mm]
０１～３２ ４０ Initial Time [sec]
０１～３２ ４１ Maximum 1 ST Time [sec] Time
０１～３２ ４２ Maximum 2 ND Time [sec]
０１～３２ ５０ Initial Speed [mm/sec]
０１～３２ ５１ Free Run Speed [mm/sec]
０１～３２ ５２ Slow Down Speed [mm/sec]
０１～３２ ５３ Load Speed [mm/sec]
Speed
０１～３２ ５４ Return Speed [mm/sec]
０１～３２ ６０ Free Run Distance ［mm］
０１～３２ ６１ Recovery Time [sec]
０１～３２ ６２ Operation Finish Return Position ［mm］
０１～３２ ６３ ∆ｆ ［KN］
Special Setting
０１～３２ ６４ Distance Off Set ［mm］
Chapter 6: System Operation