Yokogawa DA100 - Manual (Page 46)

IM DA100-11E 5-4
5.3 Setting a Channel No., and Alarm Output Relay
No.
Channel and relay numbers are expressed as shown below in three characters.
Unit No. + Slot No. + Number in slot
1 2 3
Channel/relay No.
Slot No. (In case of channel/relay No. 10, Slot No. + 1)
Unit No. ("A" for optional computation channel)
Channel Number
Stand-alone model(DA100-1) Expandable model(DA100-2)
Unit No. 0 0 to 5 (Subunit: DS400/DS600)
Slot No. 0 to 5 0 to 5
Channel No. 1 to 10 (CH10: 0)* 1 to 10 (CH10: 0)*
*: For CH10, the channel number digit is expressed by 0 and the slot number digit, by slot number + 1.
Note
• If successive channel numbers are to be specified, enter as ABC-DE, where
ABC: the above 3-digit channel number (unit no., slot no., and channel no.)
DE: the channel number except the unit number (slot no., and channel no.)
Successive channels can only be specified for a unit.
• The input module cannot be mounted to the DA100 main unit of an extended model.
Relay Number
Stand-alone model(DA100-1) Expandable model(DA100-2)
Unit No. 0 I (DA100 main unit)
0 to 5 (Subunit: DS400/DS600)
Slot No. 0 to 5 0 to 5
Relay No. 1 to 10 (Relay No. 10: 0)* 1 to 10 (Relay No. 10: 0)*
*: For relay No. 10, the channel number digit is expressed by 0 and the slot number digit, by slot number + 1.
Example
• Channel 9 of the module mounted in slot 2 of the unit 3 of the extended model: 329
• Relay of No. 10 of the module mounted in slot 2 of the unit I of the extended model: I30
P O W E R
1 0 0 - 2 4 0 V 5 0 / 6 0 H z 5 5 V A M A X
DATA ACQUITION UNIT
STATUS
Slot 0
Slot 1
Slot 2
Slot 3
Unit I
(DA100)
P O W E R
1 0 0 - 2 4 0 V 5 0 / 6 0 H z 7 0 V A M A X
STATUS
Slot 0
Slot 1
Slot 2
Slot 3
Slot 4
Slot 5
Unit 0
0 to 5
(DS400/DS600)
SUB UNIT
P O W E R
1 0 0 - 2 4 0 V 5 0 / 6 0 H z 7 0 V A M A X
STATUS
Slot 0
Slot 1
Slot 2
Slot 3
Slot 4
Slot 5
SUB UNIT
P O W E R
1 0 0 - 2 4 0 V 5 0 / 6 0 H z 7 0 V A M A X
DATA ACQUITION UNIT
STATUS
Slot 0
Slot 1
Slot 2
Slot 3
Slot 4
Slot 5
Unit 0
Stand-alone model Expandable model
Module
1
3
5
7
9
2
4
6
8
10
2
4
6
8
10
1
3
5
7
9
*1
*1 : The unit number of the sub-unit is the number
set by the switch located on each unit below
slot 2.
Maku sure the settings conform the switch
setting.
Unit No.
setting switch