Yokogawa DA100 - Manual (Page 56)

IM DA100-11E 6-4
• Setting the output relay number of a module
that is not connected to p5 causes an error. For
the method to specify the relay number, see
page 5-4.
• Hysteresis should be set using the XA
command.
• The computation channel hysteresis is fixed to
0.
• The optional computation channel number for
a stand-alone model is A01 to A30.
SD Sets date and time.
Mode Operation mode
Setting SDp1, p2<terminator>
p1 Date (year, month, day)
p2 Time (hour, minute, second)
Example Set the clock in the DA100 to 1 o’clock pm, (0
min., 0 sec.) on July 1, 1996.
SD96/07/01, 13:00:00
Comments • The formats for p1 and p2 are fixed at 8
characters. Set them in the following manner:
p1 = YY/MM/DD (Last two digits of the year,
month, day)
p2 = HH:MM:SS (Hour:minute:second)
• An error will occur when a space exists within
the parameter.
SV Sets a moving average.
Mode Operation mode
Setting SVp1, p2<terminator>
p1 Channel number (001 to 560)
p2 Number of moving averages (0 to 64)
0 = Off
Example Take moving averages 64 times in the input of
subunit 0, channel 01.
SV001, 64
SY Sets the execution of copying between
channels for channel setting
parameters.
Mode Operation mode
Setting SYp1, p2, p3, p4, p5-p6<terminator>
p1 Copying of range parameter including unit
(on, off)
p2 Copying of alarm parameter (on, off)
p3 Copying of moving average parameter
(on, off)
p4 Copying of source channel number (001
to 560)
or computation channel number (A01 to
A60)
p5 Head channel number of copying
destination (001 to 560)
or computation channel number (A01 to
A60)
p6 Copying destination end channel (01 to
60)
Example Copy only the range setting data in channel 01 of
subunit 0 to channel 01 to channel 60 of subunit
1.
SYON, OFF, OFF, 001, 101-60
Copy only the range setting data in channel 02 of
subunit 0 to channel 03 of subunit 0.
SYON, OFF, OFF, 002, 003
Comments • If a copy is to be set to successive channels,
insert a minus sign (-) between the head channel
number and the tailing channel number.
However, channels that can be set successively
are effective only in the same subunit.
• Copying between the measurement channel and
computational channel cannot be done.
• For stand-alone models computation channel
number is A01 to A30.
SX Sets channels in a group.
Mode Operation mode
Setting SXp1, p2<terminator>
p1 Group number (G01 to G07)
p2 Channel number (up to 36 characters)
Example Set channels from channel 1 in slot 1 of unit 4 to
channel 10 in slot 3 of unit 4 and channel 5 in slot
4 of unit 4 to group 3.
SXG03, 411-440, 445
Comments • Delimit the channels set in p2 with a comma
(,). For successive channels, insert a “-” (minus)
between the first and last channels.
SI Sets the timer.
Mode Operation mode
Setting SXp1, p2, p3, p4<terminator>
p1 Timer number (1 to 6)
p2 ABSOLUTE: Absolute time
RELATIVE: Relative time
p3 Time interval
For ABSOLUTE
1 min, 2 min, 3 min, 4 min, 5 min, 6 min,
10 min, 12 min, 15 min, 20 min, 30 min,
1 h, 2 h, 3 h, 4 h, 6 h, 8 h, 12 h, 24 h
For RELATIVE,
Fixed to 8 characters
DD HH:MM
DD: Day
HH: Hour
MM: Minute
p4 Reference time (fixed to 5 characters)
HH:MM
HH: Hour
MM: Minute
Example Set timer No. 3 to intervals of 15 minutes each
starting at 15:15.
SI3, ABSOLUTE, 15 min, 15:15
Comments • p4 is effective when p2 is ABSOLUTE.
• In ABSOLUTE, the time interval set with p3 is
used from the time set with p4.
• In RELATIVE, the time interval set with p3 is
used from the time when the timer setting is
completed, the power is turned on, or the set
timer is executed.
SQ Sets a match time.
Mode Operation mode
Setting SQp1, p2<terminator>
p1 Match time number (1 to 3)
p2 Time (fixed to 11 characters)
DD HH:MM (day hour:minute)
Example Set a match time 1 at 12:00 on the 15th day.
SQ1, 15 12:00:00
Comments • When the time set here is reached, the operation
set for the match time is executed.
6.1 Setting Command