MTS Multipurpose Elite Test User Manual
Multipurpose elite test design guide
Advertising
Table of contents
Document Outline
- 1.0 Technical Support
- 2.0 Preface
- 3.0 Designing a Test
- 3.1.0 Introduction
- 3.2.0 Test Design WorkFlow
- 3.2.1.0 Using the Multipurpose Application with Controller Software
- 3.2.2.0 Creating Tests Overview
- 3.2.3.0 Test Activities Overview
- 3.2.4.0 Working with Test-Run Display Devices
- 3.2.5.0 Test Execution Overview
- 3.2.6.0 Model 494.05 Handset Station Activities
- 3.2.7.0 Generating a Report in MP
- 3.2.8.0 Generating a Report Using the Excel Reporter Add-In
- 4.0 Working with Resources
- 5.0 Creating Tests
- 5.1.0 Installing MTS TestSuite Simulation Software
- 5.2.0 Creating Ramp and Cycle Test
- 5.2.1.0 Ramp and Cycle Test Design Overview
- 5.2.2.0 Opening a Station Configuration and Starting the MPE Application
- 5.2.3.0 Creating an Empty Test
- 5.2.4.0 Adding a Ramp Activity
- 5.2.5.0 Adding a Cycle Activity
- 5.2.6.0 Adding a Second Ramp Activity
- 5.2.7.0 Adding a Signal Scope Monitor
- 5.2.8.0 Checking the Test Procedure
- 5.2.9.0 Adding Variables
- 5.2.10.0 Adding an Input Variables Activity
- 5.2.11.0 Adding Parallel Paths and a Data Acquisition Activity
- 5.2.12.0 Running the Test Procedure
- 5.3.0 External Commands
- 5.3.1.0 External Command Test Overview
- 5.3.2.0 Controls That Affect External Command
- 5.3.3.0 Simulating an External Command Input in the Station Configuration
- 5.3.4.0 Simulating a Sine Wave Command with a Calculation
- 5.3.5.0 Setting Station Manager Application Command Options
- 5.3.6.0 Showing the Station Manager Application Setpoint and Span Controls
- 5.3.7.0 Starting the MPE Application and Creating a New Test Shell
- 5.3.8.0 Adding an External Command Activity
- 5.3.9.0 Adding a Signal Scope Monitor
- 5.3.10.0 Set MPE Application Command Settings
- 5.3.11.0 Starting the Test Procedure and Observing the Response
- 5.3.12.0 Stop the Test Procedure and Observe the Response
- 5.3.13.0 Resume the Test and Change Setpoint and Span
- 5.4.0 External Command Considerations
- 6.0 Creating Advanced Tests
- 6.1.0 Introduction
- 6.2.0 Working with Profiles
- 6.2.1.0 Profile Test Overview
- 6.2.2.0 Controls That Affect Profiles
- 6.2.3.0 Creating a Profile
- 6.2.4.0 Creating Controller Resource Actions that Map to the Profile
- 6.2.5.0 Starting the MPE Application and Creating a New Test Shell
- 6.2.6.0 Adding a Profile Activity
- 6.2.7.0 Adding a Monitor Display to Show the Profile Waveform
- 6.2.8.0 Adding a Monitor Display to Track Profile Passes
- 6.2.9.0 Adding a Monitor Display to Show When Part of the Profile Plays Out
- 6.2.10.0 Start the Test Procedure and Observe the Response
- 6.2.11.0 Considerations for Profile Design
- 6.2.11.1.0 Profile Types
- 6.2.11.2.0 Using ALC with the Profile Activity
- 6.2.11.3.0 General Profile Syntax Requirements
- 6.2.11.4.0 Header Data Syntax
- 6.2.11.5.0 Action and Counter Syntax
- 6.2.11.6.0 Channel Header Syntax
- 6.2.11.7.0 Channel Data Syntax
- 6.2.11.8.0 Dimensions
- 6.2.11.9.0 Normalized Dimensions
- 7.0 MTS Controller Software
- 8.0 Appendix A: MPE for MPT Users
- Index