Document Outline

• ATCA-7350
• About this Manual
  • Overview of Contents
  • Abbreviations
  • Conventions
  • Summary of Changes
• Introduction
  • 1.1 Features
  • 1.2 Standard Compliances
  • 1.3 Ordering Information
    • 1.3.1 Supported Board Models
    • 1.3.2 Board Accessories
• Hardware Preparation and Installation
  • 2.1 Overview
  • 2.2 Unpacking and Inspecting the Blade
  • 2.3 Environmental and Power Requirements
    • 2.3.1 Environmental Requirements
    • 2.3.2 Power Requirements
  • 2.4 Precautions
    • 2.4.1 ESD Prevention
  • 2.5 Checking the Installation Environment
    • 2.5.1 Wearing the ESD-Preventive Wrist Strap
    • 2.5.2 Removing Blank Filler Blades
  • 2.6 Installing Blade Accessories
    • 2.6.1 Precautions
    • 2.6.2 Optional Components Supported by the ATCA-7350
    • 2.6.3 Preparations
    • 2.6.4 DIMM
      • 2.6.4.1 Installing the DIMM
      • 2.6.4.2 Replacing the DIMM
    • 2.6.5 Hard Disk
      • 2.6.5.1 Installing the Hard Disk
      • 2.6.5.2 Replacing the Hard Disk
  • 2.7 Installing and Removing the Blade
    • 2.7.1 Installation
      • 2.7.1.1 Installing the ATCA-7350 in a Powered Shelf
      • 2.7.1.2 Checking the Installation
      • 2.7.1.3 Blade Power-On
    • 2.7.2 Removal
      • 2.7.2.1 Power Off
      • 2.7.2.2 Removing the ATCA-7350
      • 2.7.2.3 Removing the RTM-ATCA-7x50
• Controls, LEDs and Connectors
  • 3.1 Overview
  • 3.2 Blade Layout
  • 3.3 Face Plate
  • 3.4 Connectors
    • 3.4.1 Backplane Connectors
      • 3.4.1.1 Zone1 (P10) Power connector
      • 3.4.1.2 Zone2 Data Transport ZD connector
      • 3.4.1.3 Zone 3 Connectors
    • 3.4.2 Face Plate (ATCA-7350) Connectors
      • 3.4.2.1 SAS HDDs
      • 3.4.2.2 SAS Ports
      • 3.4.2.3 USB Ports
      • 3.4.2.4 Serial Port
    • 3.4.3 Onboard Jumpers
  • 3.5 LEDs
• Functional Description
  • 4.1 Overview
    • 4.1.1 Processor
    • 4.1.2 Chipset
    • 4.1.3 Memory
    • 4.1.4 I/O Features (with RTM-ATCA-7350)
    • 4.1.5 I/O Features (with RTM-ATCA-7150)
    • 4.1.6 Front Panel
    • 4.1.7 Onboard Storage
    • 4.1.8 Management
    • 4.1.9 Form Factor
    • 4.1.10 Power
    • 4.1.11 Environment
    • 4.1.12 Target Certifications
    • 4.1.13 Design Standard
  • 4.2 Block Diagram
  • 4.3 Processors
    • 4.3.1 Features
    • 4.3.2 Processor Locations
  • 4.4 Chipset
    • 4.4.1 Memory Controller Hub
    • 4.4.2 Enterprise South Bridge
  • 4.5 Memory
  • 4.6 I/O
    • 4.6.1 Keyboard and Mouse
    • 4.6.2 Serial Port
    • 4.6.3 Real-Time Clock
    • 4.6.4 Gigabit Ethernet (ATCA-7350 with RTM-ATCA-7350)
    • 4.6.5 Gigabit Ethernet (ATCA-7350 with RTM-ATCA-7150)
    • 4.6.6 Fiber Channel (ATCA-7350 with RTM-ATCA-7350)
    • 4.6.7 Fiber Channel (ATCA-7350 with RTM-ATCA-7150)
    • 4.6.8 SAS HDD
    • 4.6.9 SAS Port
    • 4.6.10 USB Port
  • 4.7 BIOS BOOT Banks
    • 4.7.1 Redundant BIOS
  • 4.8 Intelligent Platform Management Controller
    • 4.8.1 Functions
  • 4.9 Reset Methods
  • 4.10 WDTs
    • 4.10.1 WDT#1
    • 4.10.2 WDT#2
  • 4.11 Power Supplies
  • 4.12 ACPI
  • 4.13 On-Board USB Flash
  • 4.14 SOL Daughter Card
• System Management
  • 5.1 Overview
  • 5.2 Sensor Information
    • 5.2.1 Temperature Sensor Location
    • 5.2.2 Critical Temperature Limits
  • 5.3 Flash ROM Recovery Mechanism
  • 5.4 Setting Up a Serial Over LAN Session
    • 5.4.1 Remote Blade Setup
    • 5.4.2 Client Setup
• BIOS
  • 6.1 Overview
  • 6.2 Introduction
  • 6.3 BIOS Flash Memory Organization
  • 6.4 System Management BIOS
  • 6.5 Legacy USB Support
  • 6.6 Boot Options
    • 6.6.1 CD-ROM and Network Boot
    • 6.6.2 Booting Without Attached Devices
    • 6.6.3 Boot Option Configuration via IPMI
  • 6.7 Fast Booting Systems
    • 6.7.1 Quick Boot
  • 6.8 BIOS Security Features
  • 6.9 BIOS Setup
    • 6.9.1 Main Menu
    • 6.9.2 Advanced Menu
      • 6.9.2.1 CPU Configuration Submenu
      • 6.9.2.2 Memory Configuration Submenu
      • 6.9.2.3 Event Log Configuration Submenu
      • 6.9.2.4 USB Configuration Submenu
      • 6.9.2.5 IPMI 2.0 Configuration Submenu
      • 6.9.2.6 MPS Configuration Submenu
      • 6.9.2.7 Remote Access Configuration Submenu
      • 6.9.2.8 PXE Function Configuration Submenu
      • 6.9.2.9 MCFG Table Support item
    • 6.9.3 Boot Menu
      • 6.9.3.1 Boot Settings Configuration Submenu
      • 6.9.3.2 Boot Device Priority Submenu
    • 6.9.4 Security Menu
    • 6.9.5 Exit Menu
• RAID 1 Operations
  • 7.1 Overview
  • 7.2 Checking RAID 1
  • 7.3 Setting and Synchronizing RAID 1
  • 7.4 Activating RAID 1
  • 7.5 Deleting RAID 1
  • 7.6 Distinguishing Hard Disks
• Software Upgrade
  • 8.1 Overview
  • 8.2 BIOS Upgrade
  • 8.3 Firmware Upgrade
    • 8.3.1 FPGA Upgrade
    • 8.3.2 IPMC FirmwareUpgrade
    • 8.3.3 SDR Information Upgrade
    • 8.3.4 SOL Firmware Upgrade
  • 8.4 EEPROM Upgrade
  • 8.5 Automated Firmware Upgrade
• Addressing
  • 9.1 PCI Configuration Map
  • 9.2 Configuration Registers
    • 9.2.1 Configuration Address Register MCH CONFIG_ADDRESS
    • 9.2.2 Configuration Data Register MCH CONFIG_ADDRESS
  • 9.3 I/O Address Assignments
  • 9.4 Memory Map
• A Troubleshooting
  • A.1 Overview
  • A.2 Precautions
  • A.3 Principles
  • A.4 Resources
  • A.5 Contacting Artesyn Embedded Technologies for Technical Support
  • A.6 LED Display Exceptions
    • A.6.1 LEDs Are Off
  • A.7 Power-On Startup Exceptions
  • A.8 Component Exceptions
    • A.8.1 Component Is Unavailable
    • A.8.2 Number of DIMMs Is Inconsistent
  • A.9 Power Exceptions
    • A.9.1 ATCA-7350 Cannot Be Started
    • A.9.2 ATCA-7350 Automatically Shuts Down
  • A.10 Peripheral Exceptions
    • A.10.1 Keyboard Cannot Be Used
    • A.10.2 Mouse Cannot Be Used
    • A.10.3 Monitor Remains Dark
    • A.10.4 Monitor Display Is Abnormal
    • A.10.5 No Information Is Displayed on the Monitor
  • A.11 Other Exceptions
    • A.11.1 USB Interface Cannot Be Used
    • A.11.2 Network Connection Is Faulty
    • A.11.3 A Fault Occurs in Software
  • A.12 Uncertain Exceptions
  • A.13 POST Code Checkpoints
  • A.14 DIM Code Checkpoints
  • A.15 ACPI Code Checkpoints
• B Related Documentation
  • B.1 Artesyn Embedded Technologies - Embedded Computing Documentation
  • B.2 Related Specifications
• Safety Notes
• Sicherheitshinweise