Orion System RNE Modular Controller - Manual (Page 20)

Zone
Zone
OVERVIEW
RNE Modular Controller Field Technical Guide 20
Duct Mounted CO
2
Sensor
The OE256-02 CO
2
Sensor is used for sensing the current CO
2
level
in the HVAC unit’s return air stream. This is useful when you want an
average CO
2
reading in the area served by the HVAC unit or when you
don’t want a wall mounted CO
2
sensor due to sensor tampering concerns
in the space.
The OE256-02 Duct Mounted Return Air CO
2
Sensor is comprised of
the OE256-01 CO
2
Sensor and the WattMaster Aspiration Box Assembly.
The Duct Mounted Return Air CO
2
Sensor is designed to be mounted in
the return air duct of the HVAC unit and uses its integral aspiration box
to sample the CO
2
level in the duct. See the dimensional and installa-
tion information in Figure 9 below for wiring and installation details.
Figure 9: OE256-02 - Duct Mounted CO
2
Sensor Wiring
Ducted Mounted CO
2
Sensor
RNE Controller
TSDRSC Cable
TSDRSC Cable
Duct Mounted CO Sensor
2
Wall Mounted
Digital Room Sensor
Connection Of Wall
Mounted
Digital Room Sensor
(When Used)
Display Override
OVERRIDE ALARM
Note:
1.) The CO Sensor Always Connects To The RNE Controller
Using A TSDRSC Cable Of The Required Length. If Also
Using A Digital Room Sensor, Connect The Digital Room
Sensor To The C
Sensor Using Another TSDRSC Cable
Of The Required Length. The Total Length Of Cable For All
Sensor Cables Combined Cannot Exceed 160 Feet.
2
2
O
RELAY CONTACT
RATING IS 1 AMP
MAX @ 24 VAC RS-485 COMMUNICATION LOOP. WIRE
“R” TO “R”, “T” TO “T” “SHLD” TO “SHLD”
FAN
RELAY 2
RELAY 3
RELAY 4
RELAY 5
RELAY
COMMON
IC DIGITAL
SENSOR
2 IC
EXPANSION
2 STATIC
PRESSURE
AI1 = SPC (SPACE TEMPERATURE SENSOR)
AI2
AI3
AI4
AI5
AI7
A01
A02
= SAT (SUPPLY AIR TEMPERATURE SENSOR)
= RAT (RETURN AIR TEMPERATURE SENSOR)
= OAT (OUTDOOR AIR TEMPERATURE SENSOR)
= SUCTION PRESSURE SENSOR
= SPACE TEMPERATURE SENSOR SLIDE ADJUST
OR VOLTAGE RESET SOURCE
= ECONOMIZER (2-10 VDC OUTPUT)
= SUPPLY FAN VFD (0-10 VDC OUTPUT)
ANALOG INPUT JUMPER SETTINGS
MUST BE SET AS SHOWN FOR
PROPER OPERATION 24 VAC POWER ONLY
WARNING! POLARITY MUST BE OBSERVED
OR THE CONTROLLER WILL BE DAMAGED
www.orioncontrols.com
AI1
AI2
AI3
AI4
THERM
THERM
THERM
THERM
THERM
THERM
4-20mA
4-20mA
4-20mA
4-20mA
4-20mA
4-20mA
0-10V
0-10V
0-10V
0-10V
0-10V
0-10V
0-5V
0-5V
0-5V
0-5V
0-5V
0-5V
AI5
AI7
ANALOG INPUT
JUMPER
SETTINGS
WattMaster Label
#LB102033-01
OE332-23-VCMX-A VCM-X CONTROLLER
WA
RN
IN
G
OBSERVE POLARITY
RELAY CONTACT
RATING IS 1 AMP
MAX @ 24 VAC RS-485 COMMUNICATION LOOP. WIRE
“R” TO “R”, “T” TO “T” “SHLD” TO “SHLD”
FAN
RELAY 2
RELAY 3
RELAY 4
RELAY 5
RELAY
COMMON
IC DIGITAL
SENSOR
2 IC
EXPANSION
2 STATIC
PRESSURE
ANALOG INPUT JUMPER SETTINGS
MUST BE SET AS SHOWN FOR
PROPER OPERATION 24 VAC POWER ONLY
WARNING! POLARITY MUST BE OBSERVED
OR THE CONTROLLER WILL BE DAMAGED
AI1
AI2
AI3
AI4
THERM
THERM
THERM
THERM
THERM
THERM
4-20mA
4-20mA
4-20mA
4-20mA
4-20mA
4-20mA
0-10V
0-10V
0-10V
0-10V
0-10V
0-10V
0-5V
0-5V
0-5V
0-5V
0-5V
0-5V
AI5
AI7
ANALOG INPUT
JUMPER
SETTINGS
WattMaster Label
#LB102073-01-A
Rev.: 1A
VCM-X MODULAR E-BUS CONTROLLER
Orion No.:OE332-23E-VCMX-MOD-A
AAON No.:
V07150
AI1 = SPC (SPACE TEMPERATURE SENSOR)
AI2
AI3
AI4
AI5
AI7
A01
A02
= SAT (SUPPLY AIR TEMPERATURE SENSOR)
= RAT (RETURN AIR TEMPERATURE SENSOR)
= OAT (OUTDOOR AIR TEMPERATURE SENSOR)
= SUCTION PRESSURE SENSOR (FROM EXP. MODULE)
= SPACE TEMPERATURE SENSOR SLIDE ADJUST
OR VOLTAGE RESET SOURCE
= ECONOMIZER (2-10 VDC OUTPUT)
= SUPPLY FAN VFD (0-10 VDC OUTPUT)
LED BLINK CODES
LED NAME STATUS1 STATUS2
NORMAL OPERATION 0 1
SAT FAIL 1 2
OAT FAIL 2 2
SPC FAIL 3 2
MODULE ALARM 4 2
MECH COOL FAIL 1 3
MECH HEAT FAIL 2 3
FAN PROOF FAIL 3 3
DIRTY FILTER 4 3
EMERGENCY SHUTDOWN 5 3
LOW SAT 1 4
HIGH SAT 2 4
CONT. TEMP COOL FAIL 3 4
CONT. TEMP HEAT FAIL 4 4
PUSH BUTTON OVR 1 5
ZONE OVR 2 5
OUTPUT FORCE ACTIVE 0 6
E-BUS
CONNECTOR