Orion System RNE Modular Controller - Manual (Page 8)

OVERVIEW
RNE Modular Controller Field Technical Guide 8
Parts and Descriptions
PART NO. PART DESCRIPTION ILLUSTRATION
PAGE
NO.
OE370-23-HP2C2-A Two Condenser Head Pressure Module
Includes: Two Condenser Head Pressure Module in a plastic enclosure
and E-BUS Modular Cable. This module is used on units with 2 physical-
ly separate condenser sections and is able to monitor up to 4 individual
head pressure transducers (2 per section) to control the Condenser
Fans or Water Valves based on the highest of the 2 readings for each
section. It is also capable of monitoring a Heating Enable control signal
(Heat Pump Mode) and forces the Condenser Signal to 100% while in
this mode. This module can be used as a communicating module with
the RNE Controller.
1003
1002 10uF
300
1 2
4
8
SER
IA L #
C2
D3
D4
R7 R9
R11 R12
R13 R14
R23
R24
R25
R26
R28 R29 R30
SW1
D12
D13
R53 R54
TB3
C20
R3
4
R
50
SW2
+5V
SIG 2
GND
1003 1002 10uF
1003 1002 10uF
1003 1002 10uF
4751 4751 4751 4751
OF
F
OF
F
OP
TI
ON
S
ALARM STAT COMM
300 4
4
1002 1002 1002 1002 1002 1002 1002 1002
RELAYS
ANALOG
ADDRESS
+5V
SIG 3
GND
+5V
SIG 4
GND
BIN 1
COM
+5V
SIG 1
GND
BIN 2
R1
R2
R3
R4
Rc
AO1
AO2
GND
PWM1-
PWM1+
PWM2-
PWM2+
.01uF PWR
Pages
42,46
OE210
OE211
OE212
OE213
Standard Room Sensor–Plain, w/Override,
w/Override & Slide Adjust & w/Slide Adjust Only
Includes: Standard Room Sensor - Plain, with Override, with Override
and Slide Adjust & with Slide Adjust only. For wall mounting. Use with
RNE Controller only. Connects to controller via fi eld fabricated wiring.
TMP
GND
AUX
OUT
Page
21
OE217-00 Digital Room Sensor - Temp. Only
LCD Display and keypad allow for setpoint adjustment, override, and
display of certain status and setpoints. The OE217-00 is used with the
RNE Controller for room air temperature sensing applications. Uses I
2 C
cable.
Display Override
OVERRIDE ALARM
Page
19
OE217-01 Digital Room Sensor - Temp and Humidity
LCD Display and keypad allow for setpoint adjustment, override, and
display of certain status and setpoints. The OE217-01 is used with the
RNE Controller for room air temperature and humidity sensing applica-
tions. Uses Uses I
2 C cable.
Display Override
OVERRIDE ALARM
Page
19
OE256-01 CO
2
Wall-Mounted Sensor
Used with the RNE for CO
2
sensing applications where wall mounting in
the space is desired. Connects to the RNE Controller with an I 2 C cable
of required length. Cable sold separately.
Page
19
OE256-02 CO
2
Duct Sensor with Pickup Tube
Used with the RNE Controller for duct mounted CO
2
sensing applica-
tions. Connects to the RNE Controller with an I 2 C cable of required
length. Includes: Duct Mounted CO
2
Sensor, Integral Aspiration Box,
Airfl ow Pickup Tube and 10 ft. I 2 C Cable.
Page
20
TSDRSC-05
TSDRSC-10
TSDRSC-25
TSDRSC-40
TSDRSC-80
TSDRSC-120
TSDRSC-160
Digital Sensor Cable Assembly
Includes: Digital Sensor Cable Assembly. Cable assembly has male
RJ-45 modular connectors on both ends. For use with the Digital Room
Temperature Sensor, Digital Room & Temperature Sensor, Wall Mounted
CO
2
Sensor & Duct Mounted CO
2
Sensor. These cables are used
with the OE332-23E-RNE – RNE Controller and the OE742-31-VAVZ,
OE742-32-VAVZ, OE744-31-VAVZ, and OE744-32-VAVZ – VAV/Zone
Controller Actuator Packages. The TSDRSC Cables are available in 5,
10, 25, 40, 80, 120 & 160 feet lengths. The maximum length of cable
allowed is 160 feet for a CO
2
Sensor and 160 Feet for a Digital Room
Sensor. The total combined length of cable allowed when both a CO
2
Sensor and Digital Room Sensor is used is 160 feet.
Page
19
MS000029 Cable Coupler for TSDRSC Cables
Includes: Sensor Cable Coupler. Used to connect TSDRSC cables
together when lengths inbetween available cable sizes are required.
Female RJ-45 to Female RJ-45. Maximum 1 Cable Coupler per cable
run.
Page
19