Verilink QPRI 2921 (880-503143-001) Product Manual - Manual (Page 39)

Configuring the QPRI 2921 Via the NCM 2000 Craft Interface
Verilink QPRI 2921 3-5
Administration Menu
When the shelf/slot address for the QPRI 2921 is selected from the
NCM Main Menu and the screen is refreshed by pressing E
NTER , the
Main Menu’s prompt displays the shelf/slot address of the QPRI
2921. Command O displays the NCM Controller Administration
Menu’s QPRI 2921 Card Administration Submenu.
Figure 3-2 NCM Controller Administration Menu (QPRI 2921 Card Administration Submenu)
Table 3-3 Card Administration Submenu Commands
Command Description Options
O Switch over permanent—This option designates the partition A or B firmware
version when you reboot the card. Assign a permanent partition to boot from
in case of power failure. Before choosing a partition, ensure that a firmware
version exists on both partitions using the Query Firmware command below.
1) A
2) B
Q Query Firmware—Use this option to display the firmware versions and their
status for the A and B flashbanks (unless a flashbank is empty).
R Reset Card—This option reboots the module.
Y Switch Over Once—Use this option when testing new firmware versions to
change from partition A to B or vice versa. The next time you reboot, the
module will use the original partition/flashbank. Though you can use this
option for diagnostics, you should nevertheless indicate a permanent partition
to boot from in case of power failure.
1) A
2) B
I Change Site Name—Use this option to specify the site name for the QPRI.
Limited to 19 viewable characters. All reports will contain this information
which—in case of a problem—will help to identify the module location.
U Clear Card Configuration—This option clears the configuration of the card and
returns it to the default settings. NOTE: Use with Caution!
[0.0.0.5] [1,2] QPRI > u [0.0.0.5] [1,2] QPRI > u [0.0.0.5] [1,2] QPRI > u [0.0.0.5] [1,2] QPRI > u
Clear card configuration on shelf 1 slot 2 (Y/N)? y Clear card configuration on shelf 1 slot 2 (Y/N)? y Clear card configuration on shelf 1 slot 2 (Y/N)? y Clear card configuration on shelf 1 slot 2 (Y/N)? y
Card configuration cleared Card configuration cleared Card configuration cleared Card configuration cleared
Yes or No
(Y/N)
X Exit this Screen—Returns you to the Main Menu, Table 3-1.
-- NCM CONTROLLER ADMINISTRATION MENU -- -- NCM CONTROLLER ADMINISTRATION MENU -- -- NCM CONTROLLER ADMINISTRATION MENU -- -- NCM CONTROLLER ADMINISTRATION MENU --
Date/Time/Zone: 05-31-01 17:27:46
Date/Time/Zone: 05-31-01 17:27:46 Date/Time/Zone: 05-31-01 17:27:46 Date/Time/Zone: 05-31-01 17:27:46
Node Address: [127.255.255.0]
Node Address: [127.255.255.0] Node Address: [127.255.255.0] Node Address: [127.255.255.0]
Node ID: 20
Node ID: 20 Node ID: 20 Node ID: 20
Site Name:
Site Name: Site Name: Site Name:
System Uptime: 17:25:27
System Uptime: 17:25:27 System Uptime: 17:25:27 System Uptime: 17:25:27
--- QPRI -- Card Administration -- [01,02] ---
--- QPRI -- Card Administration -- [01,02] --- --- QPRI -- Card Administration -- [01,02] --- --- QPRI -- Card Administration -- [01,02] ---
O) switch over permanent
O) switch over permanent O) switch over permanent O) switch over permanent
Q) query firmware
Q) query firmware Q) query firmware Q) query firmware
R) reset card
R) reset card R) reset card R) reset card
Y) switch over once
Y) switch over once Y) switch over once Y) switch over once
I) change site name
I) change site name I) change site name I) change site name
U) clear card configuration
U) clear card configuration U) clear card configuration U) clear card configuration
X) exit this screen
X) exit this screen X) exit this screen X) exit this screen
A [127.255.255.0] [1,2] QPRI >
A [127.255.255.0] [1,2] QPRI > A [127.255.255.0] [1,2] QPRI > A [127.255.255.0] [1,2] QPRI >