Verilink QPRI 2921 (880-503143-001) Product Manual - Manual (Page 67)

Configuring the QPRI 2921 Via the NCM 2000 Craft Interface
Verilink QPRI 2921 3-33
The port line code selection (for example, 56k or 64k circuits) can
limit a circuit’s configuration.
NOTE: Network and equipment ports must be In Service before a
circuit can be built.
When you have named a circuit and identified its source and
destination ports, allocate the source and destination timeslots.
NOTE: Build T1-to-T1 circuits first. Allocate the same-numbered
timeslots on both the source and the destination ends.
Figure 3-25 Circuit Manager Menu
NOTE: If a module is moved to a different slot, the circuit(s) must be
rebuilt.
Table 3-21 Circuit Manager Menu Commands
Command Description
A Add Circuit—Use this option to add a circuit. Figure 3-27, Table 3-22.
L Search Circuit—Use this option to search for or list existing circuits. Figure 3-28, Table 3-23.
D Delete Circuit—Use this option to remove an existing circuit. Figure 3-29, Table 3-24.
E Edit Circuit—Use this option to change characteristics of a particular circuit. Figure 3-30,
Table 3-25.
P Prev page—Views the previous page of the circuit list when the list is greater than one page.
I Activate circuit—Changes the circuit to active status.
N Next page—Views the next page of the circuit list when the list is greater than one page.
R Deactivate circuit—Changes the circuit to inactive status (The circuit will not carry data).
X Exit to Craft Main Menu—Exits the Circuit Manager Menu, and returns to the Main Menu,
Figure 3-1, Table 3-2.
A [127.255.255.0] [1,2] QPRI > A [127.255.255.0] [1,2] QPRI > A [127.255.255.0] [1,2] QPRI > A [127.255.255.0] [1,2] QPRI >
Circuit Manager -- [1,1] NCM 2000 Firmware 4.15 --
Circuit Manager -- [1,1] NCM 2000 Firmware 4.15 -- Circuit Manager -- [1,1] NCM 2000 Firmware 4.15 -- Circuit Manager -- [1,1] NCM 2000 Firmware 4.15 --
Page : 1
Page : 1 Page : 1 Page : 1
Total: 2 circuits
Total: 2 circuits Total: 2 circuits Total: 2 circuits
Name Type Mode Prio Src Port Dest Port Bus Status
Name Type Mode Prio Src Port Dest Port Bus Status Name Type Mode Prio Src Port Dest Port Bus Status Name Type Mode Prio Src Port Dest Port Bus Status
------------ ---- ---- ---- ---------------- ---------------- --- ------
------------ ---- ---- ---- ---------------- ---------------- --- ------ ------------ ---- ---- ---- ---------------- ---------------- --- ------ ------------ ---- ---- ---- ---------------- ---------------- --- ------
QPRItestC1 prim 64k crit [1, 2] QPRI net3 [1, 2] QPRI net1 INT Inacti
QPRItestC1 prim 64k crit [1, 2] QPRI net3 [1, 2] QPRI net1 INT Inacti QPRItestC1 prim 64k crit [1, 2] QPRI net3 [1, 2] QPRI net1 INT Inacti QPRItestC1 prim 64k crit [1, 2] QPRI net3 [1, 2] QPRI net1 INT Inacti
dialbackup d-bk 64k crit [1, 2] QPRI net4 [1, 2] QPRI net2 -- Inacti
dialbackup d-bk 64k crit [1, 2] QPRI net4 [1, 2] QPRI net2 -- Inacti dialbackup d-bk 64k crit [1, 2] QPRI net4 [1, 2] QPRI net2 -- Inacti dialbackup d-bk 64k crit [1, 2] QPRI net4 [1, 2] QPRI net2 -- Inacti
A) add circuit L) search circuit
A) add circuit L) search circuit A) add circuit L) search circuit A) add circuit L) search circuit
D) delete circuit E) edit circuit
D) delete circuit E) edit circuit D) delete circuit E) edit circuit D) delete circuit E) edit circuit
P) prev page I) activate circuit
P) prev page I) activate circuit P) prev page I) activate circuit P) prev page I) activate circuit
N) next page R) deactivate circuit
N) next page R) deactivate circuit N) next page R) deactivate circuit N) next page R) deactivate circuit
X) exit to craft main menu
X) exit to craft main menu X) exit to craft main menu X) exit to craft main menu
A [127.255.255.0] [1,2] QPRI >
A [127.255.255.0] [1,2] QPRI > A [127.255.255.0] [1,2] QPRI > A [127.255.255.0] [1,2] QPRI >