Verilink QPRI 2921 (880-503143-001) Product Manual - Manual (Page 66)

Configuring the QPRI 2921 Via the NCM 2000 Craft Interface
3-32 Verilink QPRI 2921
Figure 3-23 Net Port Alarm Threshold Status
Circuit Manager Menu
To access the Circuit Manager Menu from the Main Menu, enter B.
Use the Circuit Manager menu to build and maintain circuits. A
circuit is the path on which data travels between a port at the
source end and a port at the destination end. The port can be a T1
or data port. T1 port circuit size is in number of timeslots, 1
through 24. The equipment port circuit size is in 56k or 64k bit
increments.
You can mix T1 and data ports as source and destination ends.
Data-to-data port circuits are limited to inter-module only.
For ISDN (dial backup switch) circuits, the ISDN port must be the
destination port. (Equipment ports are usually the source ports and
net ports are usually the destination ports.)
Figure 3-24 Port Line Code Selection
-- QPRI 2921 NET PORT ALARM THRESHOLD STATUS MENU -- -- QPRI 2921 NET PORT ALARM THRESHOLD STATUS MENU -- -- QPRI 2921 NET PORT ALARM THRESHOLD STATUS MENU -- -- QPRI 2921 NET PORT ALARM THRESHOLD STATUS MENU --
Current Threshold Status PORT 1 PORT 2
Current Threshold Status PORT 1 PORT 2 Current Threshold Status PORT 1 PORT 2 Current Threshold Status PORT 1 PORT 2
LOF counts(exceeded) 0(N) 0(N)
LOF counts(exceeded) 0(N) 0(N) LOF counts(exceeded) 0(N) 0(N) LOF counts(exceeded) 0(N) 0(N)
interval 0 0
interval 0 0 interval 0 0 interval 0 0
LOS counts(exceeded) 0(N) 0(N)
LOS counts(exceeded) 0(N) 0(N) LOS counts(exceeded) 0(N) 0(N) LOS counts(exceeded) 0(N) 0(N)
interval 0 0
interval 0 0 interval 0 0 interval 0 0
RAI counts(exceeded) 0(N) 0(N)
RAI counts(exceeded) 0(N) 0(N) RAI counts(exceeded) 0(N) 0(N) RAI counts(exceeded) 0(N) 0(N)
interval 0 0
interval 0 0 interval 0 0 interval 0 0
AIS counts(exceeded) 0(N) 0(N)
AIS counts(exceeded) 0(N) 0(N) AIS counts(exceeded) 0(N) 0(N) AIS counts(exceeded) 0(N) 0(N)
interval 0 0
interval 0 0 interval 0 0 interval 0 0
BPV counts(exceeded) 0(N) 0(N)
BPV counts(exceeded) 0(N) 0(N) BPV counts(exceeded) 0(N) 0(N) BPV counts(exceeded) 0(N) 0(N)
interval 0 0
interval 0 0 interval 0 0 interval 0 0
ES 15min counts(exceeded) 0(N) 0(N)
ES 15min counts(exceeded) 0(N) 0(N) ES 15min counts(exceeded) 0(N) 0(N) ES 15min counts(exceeded) 0(N) 0(N)
ES 24hr counts(exceeded) 0(N) 0(N)
ES 24hr counts(exceeded) 0(N) 0(N) ES 24hr counts(exceeded) 0(N) 0(N) ES 24hr counts(exceeded) 0(N) 0(N)
SES 15min counts(exceeded) 0(N) 0(N)
SES 15min counts(exceeded) 0(N) 0(N) SES 15min counts(exceeded) 0(N) 0(N) SES 15min counts(exceeded) 0(N) 0(N)
SES 24hr counts(exceeded) 0(N) 0(N)
SES 24hr counts(exceeded) 0(N) 0(N) SES 24hr counts(exceeded) 0(N) 0(N) SES 24hr counts(exceeded) 0(N) 0(N)
Rn) Reset Registers X) exit this screen
Rn) Reset Registers X) exit this screen Rn) Reset Registers X) exit this screen Rn) Reset Registers X) exit this screen
Net 1 Net 3
Net 2 Net 4
A
B
A. Equipment to T1
B. T1 to T1