Verilink QPRI 2921 (880-503143-001) Product Manual - Manual (Page 71)

Configuring the QPRI 2921 Via the NCM 2000 Craft Interface
Verilink QPRI 2921 3-37
Edit Circuit
Submenu
To change a circuit’s characteristics, use the Edit Circuit Submenu.
However, you cannot change a circuit while it is active/running—
deactivate the circuit first, then zero it out.
To edit a circuit, enter E from the Circuit Manager menu to display
the Edit Circuit menu. To change the characteristics of a particular
circuit, specify the Circuit ID of an existing circuit.
Figure 3-30 Edit Circuit Submenu
Table 3-25
Edit Circuit Submenu Commands
Command Description Options
N Name—Circuit name (Circuit ID)—12 characters maximum
P Priority— 1) low
2) norm
3) high
4) crit
T Type—Circuit type. 1) perm
2) swit
3) prim
4) d-bk
5) bkup
M Mode—Circuit Mode 1) 64K
2) 56K
For Subrate DIU
only:
3) 38.4K
4) 19.2K
5) 9.6K
6) 4.8K
7) 2.4K
SP Source Port—Displays the Node “Map” and prompts for the SRC Port shelf,
slot. Use this option to designate the starting point of the circuit. Once the
Shelf and slot position of the Source Port has been entered, you are
prompted with 4 choices.
1) net1
2) net2
3) net3
4) net4
A [127.255.255.0] [1,2] QPRI > e A [127.255.255.0] [1,2] QPRI > e A [127.255.255.0] [1,2] QPRI > e A [127.255.255.0] [1,2] QPRI > e
Enter circuit name ( 12 char maximum ): dialbackup
Enter circuit name ( 12 char maximum ): dialbackup Enter circuit name ( 12 char maximum ): dialbackup Enter circuit name ( 12 char maximum ): dialbackup
Edit Circuit -- [1,1] NCM 2000 Firmware 4.15 --
Edit Circuit -- [1,1] NCM 2000 Firmware 4.15 -- Edit Circuit -- [1,1] NCM 2000 Firmware 4.15 -- Edit Circuit -- [1,1] NCM 2000 Firmware 4.15 --
N) Name: dialbackup P) Priority: crit
N) Name: dialbackup P) Priority: crit N) Name: dialbackup P) Priority: crit N) Name: dialbackup P) Priority: crit
T) Type: d-bk M) Mode: 64k
T) Type: d-bk M) Mode: 64k T) Type: d-bk M) Mode: 64k T) Type: d-bk M) Mode: 64k
SP) [1, 2] QPRI dat1 DP) [1, 2] QPRI net2
SP) [1, 2] QPRI dat1 DP) [1, 2] QPRI net2 SP) [1, 2] QPRI dat1 DP) [1, 2] QPRI net2 SP) [1, 2] QPRI dat1 DP) [1, 2] QPRI net2
SM) --src port chn-- DM) --dst port chn--
SM) --src port chn-- DM) --dst port chn-- SM) --src port chn-- DM) --dst port chn-- SM) --src port chn-- DM) --dst port chn--
01 02 03 04 05 06 07 08 01 02 03 04 05 06 07 08
01 02 03 04 05 06 07 08 01 02 03 04 05 06 07 08 01 02 03 04 05 06 07 08 01 02 03 04 05 06 07 08 01 02 03 04 05 06 07 08 01 02 03 04 05 06 07 08
09 10 11 12 13 14 15 16 09 10 11 12 13 14 15 16
09 10 11 12 13 14 15 16 09 10 11 12 13 14 15 16 09 10 11 12 13 14 15 16 09 10 11 12 13 14 15 16 09 10 11 12 13 14 15 16 09 10 11 12 13 14 15 16
17 18 19 20 21 22 23 .. 17 18 19 20 21 22 23 ..
17 18 19 20 21 22 23 .. 17 18 19 20 21 22 23 .. 17 18 19 20 21 22 23 .. 17 18 19 20 21 22 23 .. 17 18 19 20 21 22 23 .. 17 18 19 20 21 22 23 ..
U) Bus: -- ->-->>->> Circuit Inactive <<-<<--<-
U) Bus: -- ->-->>->> Circuit Inactive <<-<<--<- U) Bus: -- ->-->>->> Circuit Inactive <<-<<--<- U) Bus: -- ->-->>->> Circuit Inactive <<-<<--<-
A) primary circ: backup circ: dialbackup
A) primary circ: backup circ: dialbackup A) primary circ: backup circ: dialbackup A) primary circ: backup circ: dialbackup
SE) src err mask: -- C) dst call ref: --
SE) src err mask: -- C) dst call ref: -- SE) src err mask: -- C) dst call ref: -- SE) src err mask: -- C) dst call ref: --
DE) dst err mask: -- O) dbkp timeout: none
DE) dst err mask: -- O) dbkp timeout: none DE) dst err mask: -- O) dbkp timeout: none DE) dst err mask: -- O) dbkp timeout: none
G) err clr mask: no primary port
G) err clr mask: no primary port G) err clr mask: no primary port G) err clr mask: no primary port
S) Setup X) Exit
S) Setup X) Exit S) Setup X) Exit S) Setup X) Exit
A [127.255.255.0] [1,2] QPRI >
A [127.255.255.0] [1,2] QPRI > A [127.255.255.0] [1,2] QPRI > A [127.255.255.0] [1,2] QPRI >