Document Outline

• 166-369A Update Installation
• Table of Contents
• Important Safety Information
  • Look for Safety Symbol
  • Be Aware of Signal Words
  • Prepare for Emergencies
  • Avoid High Pressure Fluids
  • Be Familiar with Safety Decals
• General Information
  • Related Documents
  • Notations and Conventions
    • Call-Outs
  • Tools Required
  • Regarding Parts
    • About New Parts
    • About Existing Parts
  • Pre-Assembly Preparation
    • Work Location
• Update Underside Weldments
  • Configure Implement
  • Tack Rear Bottom Gussets
    • LH Rear Bottom Gussets
    • RH Rear Bottom Gussets
  • Install Nut Blocks
    • Install LH Nut Block
    • Install RH Nut Block
    • Finish Weld Blocks and Gussets
  • Install Box Plates
  • Install Corner Gussets
• Disconnect Implement
  • Prepare Implement
  • Disconnect Primary Hoses
  • Clear Weight Transfer Cylinders
  • Clear Link Lift Cylinders
  • Recover Pull Link Components
  • Release Lift-Assist Link
  • Uncouple Cart
  • Remove Pull Link
• Dismount Hoppers
  • Disconnect Sensors and Chain
    • Disconnect Level Sensors
    • Dismount Rate Sensor
    • Dismount Final Drive Chain
  • Dismount Meters
    • Disconnect Meter Inlet Elbows
    • Remove Meters
  • Hoist Hoppers
    • Release Hopper Mount
    • Remove Hopper Assembly
• Update Meters
  • Remove Existing Top Seal
  • Remove Meter Flute Shaft
    • Remove Old Flanges
  • Enlarge Mounting Slots
  • Drill Weep Holes
  • Install Meter Seal Flange
  • Replace Meter Shaft Mount Plates
    • Replace Right End Plates
    • Replace Left End Plates
    • Install New Top Seal
• Update Cart
  • Cart Frame Update Overview
    • Rear Gusset Plates (page 22)
    • Front Gusset Triangles (page 23)
    • Pull Bar Anchors (page 25)
    • Meter Mount Tabs (page 27)
  • Install Rear Gussets
    • Install Left Rear Gusset
    • Install Right Rear Gusset
  • Install Front Gussets
    • Install Right Front Gusset
    • Install Left Front Gusset
  • Install Pull Bar Attach Points
    • Install Pull Bar Plate
    • Install Pull Bar Anchors
      • Install Left Anchor
      • Install Right Anchor
  • Update Meter Mounts
    • Position New Meter Mounts
      • Prepare Tab Welding Sites
      • Mark Tab Welding Sites
    • Attach New Front Tabs
    • Install New Meter Mounts
  • Re-Install Meters
    • Install Hopper Supports
  • Install Pull Bars
    • Assemble Pull Bars
    • Attach Pull Bars
  • Update Cart Hydraulics
    • Route Dedicated Fold Hose
    • Mark Dedicated Fan Hose
    • Re-Route Fold Hose
    • Disconnect Bypass Hose
    • Re-Configure Inlet Fittings
    • Re-connect Fan Hoses
  • Re-Install Hoppers
    • Align Meters
    • Re-Install Final Drive Chain
    • Re-Connect Inlets/Outlets
    • Re-Install Gears
    • Re-Install Sensors
  • Update Hopper Lids
• Update Implement Frame
  • Dismount Lift-Assist
    • Disconnect Lights
    • Release Lift Link
    • Dismount Parallel Arms
    • Remove Pull Link
  • Update Rear Link Anti-Rotation
  • Update Wing Pivot Anti-Rotation
  • Update Wing Pivot Extension Tops
    • Update Front Extension Tops
    • Update Rear Extension Tops
• Update Harness
  • Dismount Existing Harnesses
  • Enumerate WSMBs
  • Install WSMBs
    • Mount Center WSMBs
      • Mount Tower B WSMB
      • Mount Tower C WSMB
    • Mount Wing WSMBs
      • Mount Tower A (Left Wing) WSMBs
      • Mount Tower D (Right Wing) WSMBs
  • Install Row Harnesses
    • Connector ID
    • Connect WSMB #1
    • Connect WSMB #4
    • Connect WSMB #2
    • Connect WSMB #5
    • Connect WSMB #3
    • Connect New WSMB #6
• Install Rear Pull Link
  • Pin Link to Main Frame
  • Connect Lift-Assist Link
  • Connect Lift Assist
  • Re-Install Parallel Arms
  • Re-Connect Lights
• Update Implement Hydraulics
  • Extend Valve Hoses
  • Relocate Valve Group
  • Protect Hose Extensions
• Re-Hitch Implement
  • Install Front Pull Link
  • Re-Connect Lift Link
  • Connect Cart and Implement
  • Re-Install Link Components
    • Store Spacers
    • Store New Lift Pins
  • Re-Install Link Lift Cylinders
  • Re-Install Weight Transfer Cylinders
  • Route Hoses and Harnesses
    • Hose ID for Pull Link Clamping
  • Connect Hoses and Harnesses
• Update Markers
  • Remove Tension Spring
  • Release Swing Pivot
  • Release Cylinder
  • Remove Arm
  • Remove Old Pivot Frame
  • Install New Pivot Frame
  • Re-Install Arm
  • Re-Attach Spring
• Update Coulters
  • Prepare Implement
  • Replace Coulter Bars
    • Remove Existing Bar
    • Install New Bar
• Close-Out
  • Reconfigure Monitor
• Appendix A - Reference Information
  • Chain Setup
    • Chain Clip Orientation
    • Chain Slack
  • Torque Values Chart
  • Hydraulic Connectors and Torque
• Appendix D - Drawings
  • 160-795D PIN RETAINER TAB
  • 160-801D FRAME NUT BLOCK
  • 160-802D FRAME EXT BOT GUSSET LH REWORK
  • 160-803D FRAME EXT BOX PLATE
  • 160-804D FRAME EXT BOT GUSSET LH REWORK
  • 160-805D FRAME EXT BOT GUSSET REWORK
  • 160-806D FRAME EXT BOT GUSSET REWORK
  • 160-807D FRAME EXT CORNER GUSSET
  • 160-808D FRAME EXT 100 DEG GUSSET
  • 160-809D FR EXT 100 DEG GUSSET REWORK
  • 160-810D FR EXT 100 DEG GUSSET REWORK
  • 160-811D WING HINGE PIN ROTATION STOP
• Appendix G - Glossary
  • Part Descriptor Abbreviations
• Appendix H - Harness
  • Tower ID
  • Secondary Hose Routing, 40-Row
    • Turrets, 40-Row, Double-Shoot, Seed
    • Mapping, 40-Row, Double-Shoot, Seed
    • Turrets, 40-Row, Double-Shoot, Fertilizer
    • 40-Row, Fertilizer
  • Harness (LH)
  • Harness (RH)
• Appendix P - Part Lists
  • Existing Parts Affected
  • 166-369A New Parts
• Index