Mount wing wsmbs, Mount tower a (left wing) wsmbs, Mount tower d (right wing) wsmbs – Great Plains 2007HD Update Installation User Manual
Page 48
44
NTA607HD or NTA2007HD
Great Plains Manufacturing, Inc.
166-370M
05/25/2011
Mount Wing WSMBs
Mount Tower A (Left Wing) WSMBs
Refer to Figure 75
260. Select one new:
166-988D BRACKET, 45DEG MODULE MOUNT
and one saved:
806-010C U-BOLT 1/2-13 X 2 1/2 X 3 1/2
and two sets saved (not shown):
804-015C WASHER LOCK SPRING 1/2 PLT
803-020C NUT HEX 1/2-13 PLT
Install the bracket
behind Tower A (left wing
seed tower), just above and parallel to the angle
that secures both towers to each other. Orient the
WSMB mounting face to the inside and rear. Secure
to tower with U-bolt
, lock washers
and
nuts
. To avoid crushing the tower tube, tighten
only to Grade 2 torque specification.
261. Select the saved WSMBs tagged as “1” and “4”:
467981100S1 INTAG WSMB MODULE 18R
and two sets new or saved:
804-006C WASHER LOCK SPRING 1/4 PLT
802-370C HHCS 1/4-20X1 3/4 GR5
Install WSMB
on the front face and WSMB
on
the rear face of the bracket
, with the connector
ports facing down and to implement center. Insert
bolts (
or
) through either WSMB, bracket
and other WSMB. Secure with lock
washers (
or
) and nuts
Mount Tower D (Right Wing) WSMBs
Refer to Figure 74
262. Select one new:
166-988D BRACKET, 45DEG MODULE MOUNT
and one saved:
806-010C U-BOLT 1/2-13 X 2 1/2 X 3 1/2
and two sets saved (not shown):
804-015C WASHER LOCK SPRING 1/2 PLT
803-020C NUT HEX 1/2-13 PLT
Install the bracket
inside Tower D (right wing
seed tower), just above and parallel to the angle
that secures both towers to each other. Orient the
WSMB mounting face to the inside and rear. Secure
to tower with U-bolt
, lock washers
and
nuts
. To avoid crushing the tower tube, tighten
only to Grade 2 torque specification.
263. Select the saved WSMB tagged as “5”:
467981100S1 INTAG WSMB MODULE 18R
and the new WSMB:
467981100S1 INTAG WSMB MODULE 18R
and two sets new or saved:
804-006C WASHER LOCK SPRING 1/4 PLT
802-370C HHCS 1/4-20X1 3/4 GR5
Install WSMB
on the front face and WSMB
on the
rear face of the bracket
, with the connector ports fac-
ing down and to implement center. Insert
bolts (
or
) through either WSMB, bracket and
other WSMB. Secure with lock washers (
or
) and
nuts
.
Figure 75: Tower A
WSMB#1, WSMB #4 Mounting
Q0124
E
A
#1
#4
917
173 947
917
187
177
917
187
177
183 954
173 947
Figure 76: Tower D
WSMB#3, WSMB #6 Mounting
Q0124
H
D
#3
#6 934
917
947
917
947
954
917
187
177
917
187
177
934
183 954
173 947
917
947
954