Document Outline

• FOREWORD
• SAFETY ALERT SYMBOLS AND SAFETY SIGNAL WORDS
  • Contact :
  • In USA:
  • Outside USA:
• REVISION LOG
• SECTION 1. SAFETY PRECAUTIONS
  • 1.1 General
    • Operator Training and Knowledge
  • 1.2 Before Operating the Lift
    • Workplace Inspection
    • Machine Inspection
  • 1.3 Operation
    • General
    • Trip and Fall Hazards
    • Electrocution Hazards
    • Tipping Hazards
    • Crushing and Collision Hazards
  • 1.4 Lifting, and Hauling
  • 1.5 Additional Hazards / Safety
• SECTION 2. PREPARATION AND INSPECTION
  • 2.1 Personnel Training
    • Operator Training
    • Training Supervision
    • Operator Responsibility
  • 2.2 Preparation, Inspection, and Maintenance
    • Pre-Start Inspection
    • Function Check
    • General
• SECTION 3. MACHINE CONTROLS, INDICATORS AND OPERATION
  • 3.1 Ground Control Station
  • 3.2 Platform/Remote Control Station
    • Control Position On The Ground:
    • Control Position From In The Platform:
    • Platform/Remote Control Station Functions
    • Platform/Remote Control Station LCD Display
• SECTION 4. MACHINE OPERATION
  • 4.1 DESCRIPTION
  • 4.2 BOOM OPERATING CHARACTERISTICS AND LIMITATIONS
    • Capacities
    • Stability
  • 4.3 ENGINE OPERATION
    • Gas/Diesel Starting Procedure
    • Gas/Diesel Engine Shutdown Procedure
    • Electric Engine Starting Procedure
  • 4.4 BASE AND BOOM/JIB ALIGNMENT
  • 4.5 TRACKS - DRIVING, STEERING AND TRACK WIDTH ADJUST
    • Track width adjust
    • Travelling (Drive and Steer)
    • Travelling (Grades and Side Slopes)
    • Jib Position for Travelling
  • 4.6 OUTRIGGER OPERATION
    • Variable Outrigger Positioning
    • Operating with Outriggers Set to 24˚ - Restricted Work Area Of Operation
    • Setting Outriggers From the Platform/Remote Console
    • Retracting The Outriggers (Reference Figure 4-6. for item numbers)
  • 4.7 BOOM/PLATFORM OPERATION
    • Overload Alarm
    • Platform Level Adjustment
    • Raise And Lower The Tower Boom
    • Raise And Lower The Main Boom
    • Telescope The Main Boom
    • Platform Rotation (Item 20, Figure 4-6.)
    • Raise And Lower The Jib (Item 21, Figure 4-6.)
    • Emergency Lowering
    • Platform Removal/Installation
  • 4.8 BATTERY CHARGING
    • Battery Charging - Daily
  • 4.9 SHUT DOWN AND PARK
  • 4.10 LIFTING AND TIE DOWN
    • Lifting
    • Tie Down
  • 4.11 MACHINE DECALS
• Section 5. EMERGENCY PROCEDURES
  • 5.1 General
  • 5.2 Incident Notification
  • 5.3 Emergency Operation
    • Power Main Cut-Off Switch Location
    • Operator Unable to Control Machine
    • Platform or Boom Caught Overhead
    • Manual Descent with Engine Running and Electrical Power
    • Manual Descent with Engine Running but without Electrical Power
    • Manual Descent without Engine and Electrical Power.
    • Outrigger/Track Movement Emergency Procedure:
  • 5.4 Safety Devices Bypass Key Use
    • Using The Emergency Descent In The Case Of An Outrigger Losing Contact With The Ground
    • Machine Realignment Emergency Procedure
• SECTION 6. GENERAL SPECIFICATIONS AND OPERATOR MAINTENANCE
  • 6.1 Introduction
  • 6.2 Operating Specifications
    • Dimensional Data
    • Chassis
    • Capacities
    • Engine Data
    • Major Component Weights
  • 6.3 Service/Maintenance
    • Lubrication
    • Rubber Track Maintenance/Replacement
    • Wire Cable Inspection
    • Wire Cable Adjustment
    • Wear Pad Inspection
    • Turntable Attach Bolts
    • Battery Maintenance and Charging
  • 6.4 PLATFORM/REMOTE CONTROL SERVICE MENU
    • Service Button
    • Menu Input
    • Errors Menu
    • Working Hours Menu
    • Set-up Menu
    • Joystick Menu
• SECTION 7. INSPECTION AND REPAIR LOG