Document Outline

• 1757-UM007D-EN-P, Process Remote I/O (RIO) Communication Interface Module User Manual
  • Table of Contents
  • Preface
    • Purpose of this Manual
    • Who Should Use this Manual
    • Additional Resources
  • 1 - Introduction
    • Introduction
    • Process Remote I/O (RIO) Communication Interface Module
    • RSLinx Software Requirements
    • ProcessLogix System Quick Start
    • RSLogix 5000 System Quick Start
    • Update the 1757-ABRIO Module’s Firmware
      • Using ControlFlash Software
      • Using NTools with ProcessLogix Software
  • 2 - Configure the 1757-ABRIO Module
    • Introduction
    • AbRioCfg Software Overview
    • Mapping and Accessing RIO Network Data
    • Installing AbRioCfg Software
    • Autoconfigure the I/O Racks
    • Adding Block Transfer Modules
      • Addressing Modes for 1771
    • Configuring Block Transfer Modules
    • Scaling
      • Input Scaling
      • Output Scaling
    • Tags Defined
      • Create a Tag
    • Mapping Data to Tags in AbRioCfg Software
      • Block Transfers
      • I/O
      • Deleting Mapped Data
    • Tips for Configuring Modules
      • Add Racks Offline
      • Delete Racks Offline
      • Change the Baud Rate Offline
    • Download the Configuration
    • Upload the Configuration
  • 3 - Creating Generic Modules in AbRioCfg Software
    • Introduction
    • Generic Module Overview
    • Generic Module Configuration File
      • Configuration Block Transfer Write
      • Data Block Transfer Read
      • Data Block Transfer Write
    • Creating a Generic Module in AbRioCfg software
  • 4 - Configuring the ProcessLogix Controller to Access Data on the 1757-ABRIO Module
    • Introduction
    • Modes of Operation
      • CONFIG Mode
      • INACTIVE Mode
      • ACTIVE Mode (Run)
      • FORCED ACTIVE Mode
    • Configure the 1757-PLX52 Controller
  • 5 - Configuring RSLogix 5000 Software to Access Data on the 1757-ABRIO Module
    • Introduction
    • Modes of Operation
      • CONFIG Mode
      • INACTIVE Mode
      • ACTIVE Mode (Run)
      • FORCED ACTIVE Mode
    • Scheduled Digital I/O Connections in RSLogix 5000 Programs
      • Scheduled Connection Types
      • Setup an Exclusive-owner Connection
      • Setup Input-only Connections
    • Unscheduled I/O Connections in ControlLogix
      • 2. Create Message Commands to Read and Write All RIO Network Data
  • 6 - Accessing Data through a DDE or OPC Server
    • Introduction
    • Accessing Data from a DDE or OPC Server
      • Configuring a Topic in RSLinx Software
      • Accessing the Data
  • 7 - Monitoring the 1757-ABRIO Module
    • Introduction
    • Monitoring the Operation
    • Monitoring Digital I/O
    • Monitoring the Data Value of Tags
    • Monitoring the Status of a Block Transfer
    • Monitoring the Scanner Log
    • Monitoring Diagnostic Counters
      • Active Rack List
      • Global Diagnostic Counters
    • Fatal Errors
  • 8 - Supported 1771 Modules
    • Introduction
    • Module Description
    • 1771-IFE Module
      • Module Configuration
      • I/O Data
      • Diagnostic Data
    • 1771-OFE Module
      • Module Configuration
      • I/O Data
      • Diagnostic Data
    • 1771-IR Module
      • Module Configuration
      • I/O Data
      • Diagnostic Data
    • 1771-IXE Module
      • Module Configuration
      • I/O Data
      • Diagnostic Data
    • 1771-IL Module
      • Module Configuration
      • I/O Data
      • Diagnostic Data
    • 1771-NOC Module
      • Module Configuration
      • I/O Data
      • Diagnostic Data
    • 1771-NOV Module
      • Module Configuration
      • I/O Data
      • Diagnostic Data
    • 1771-NIV Module
      • Module Configuration
      • I/O Data
      • Diagnostic Data
    • 1771-NR Module
      • Module Configuration
      • I/O Data
      • Diagnostic Data
  • 9 - Accessing HART Data
    • Introduction
    • Sending HART Commands Using RSLogix 5000 Software MSG
      • HART Command Data
      • Reply Data
      • Example: HART Command 36
    • 1770-HT1 Module
      • Rack Requirements
      • Configuring the 1770-HT1 Module
      • HART Command status
  • A - Specifications
  • B - Troubleshooting
    • Interpret the Status Indicators
      • RIO Status Indicator - Remote Devices Status
      • SYS Status Indicator - ControlBus Status
      • OK Status Indicator - Module Health
    • Status Display Power-up Messages
    • Power Supply Indicator
    • Interpret the Alphanumeric Display
    • Using AbRioCfg Software for Troubleshooting
    • Troubleshooting Problems
    • Using RSLogix 5000 to Diagnose Problems
      • General Tab
      • Connection Tab
      • Module Info Tab
      • Backplane Tab
    • Using Control Builder Software to Diagnose Problems
    • Troubleshooting 1757-ABRIO Module Communications
  • C - Operational Comparison Between the 1757-ABRIO Module and a PLC-5 System
    • Normal Operational Messages
    • Exception Handling Messages
  • D - Tag Descriptions for Scheduled Data in RSLogix 5000 Software
    • Configuration Tag
    • I and O Tags
    • Status Tag
    • Installation Assistance
    • New Product Satisfaction Return
  • How Are We Doing?
  • Back Cover