Furuno GP-150-DUAL - Manual (Page 5)

iii
TABLE OF CONTENTS
FOREWORD .............................................. v
SYSTEM CONFIGURATION .................... vi
1. OPERATIONAL OVERVIEW
1.1 Control Description .........................1-1
1.2 Turning On and Off the Power ......1-2
1.3 Adjusting Display Contrast and
Brilliance.........................................1-3
1.4 Display Mode ..................................1-3
1.5 Transmitting Data............................1-6
1.6 The Interface Unit ...........................1-8
2. DISPLAY AND TRACK
2.1 Enlarging/Shrinking the Display ......2-1
2.2 Display Orientation..........................2-1
2.3 The Cursor......................................2-1
2.4 Shifting the Display .........................2-2
2.5 Centering Own Ship's Position........2-2
2.6 Stopping/Starting Plotting and
Recording of Track .........................2-2
2.7 Erasing Track..................................2-3
2.8 Track Plotting Interval .....................2-4
2.9 Apportioning the Memory................2-5
2.10 Bearing Reference........................2-5
3. MARKS
3.1 Entering Marks................................3-1
3.2 Erasing Marks.................................3-1
3.3 Mark Shape ....................................3-2
3.4 Connecting Marks...........................3-2
3.5 Entering Event Marks......................3-2
3.6 Event Mark Shape ..........................3-3
3.7 Entering the MOB Mark ..................3-3
4. NAVIGATION PLANNING
4.1 Entering Waypoints.........................4-1
4.2 Editing Waypoints ...........................4-4
4.3 Erasing Waypoints ..........................4-4
4.4 Entering Routes ..............................4-5
4.5 Erasing Route Waypoints................4-6
4.6 Replacing Route Waypoints............4-7
4.7 Erasing Routes ...............................4-7
5. SETTING DESTINATION
5.1 Setting Destination..........................5-1
5.2 Cancelling Destination ....................5-5
5.3 Erasing Route Waypoints (flags).....5-6
5.4 Finding Range and Bearing
Between Two Points .......................5-7
6. SETTING UP VARIOUS DISPLAYS
6.1 The Data Display ............................ 6-1
6.2 Position Format .............................. 6-2
6.3 Demo Display ................................. 6-4
7. ALARMS
7.1 Overview ........................................ 7-1
7.2 Arrival Alarm, Anchor Watch Alarm . 7-1
7.3 Cross Track Error (XTE) Alarm....... 7-2
7.4 Speed Alarm ................................... 7-3
7.5 Trip Alarm ....................................... 7-3
7.6 Water Temperature Alarm............... 7-4
7.7 Depth Alarm.................................... 7-4
7.8 WAAS/DGPS Alarm........................ 7-4
8. MENU SETTINGS
8.1 GPS SETUP Menu ......................... 8-1
8.2 Units of Measurement .................... 8-4
8.3 Size and Brilliance of Markers ........ 8-5
8.4 Outputting Data .............................. 8-6
8.5 Receiving Data from Personal
Computer ....................................... 8-8
8.6 WAAS/DGPS Setting.................... 8-10
8.7 GPS Monitor Display .................... 8-11
9. MAINTENANCE &
TROUBLESHOOTING
9.1 Clearing the Memory ...................... 9-1
9.2 Preventive Maintenance ................. 9-2
9.3 Error Messages .............................. 9-2
9.4 Troubleshooting.............................. 9-4
9.5 Diagnostic Tests ............................. 9-5
9.6 Interface Unit IF-2500..................... 9-6
10.1 INSTALLATION
10.1 General....................................... 10-1
10.2 Display Unit ................................ 10-2
10.3 Antenna Unit............................... 10-4
10.4 Wiring ......................................... 10-8
10.5 Initial Settings ............................. 10-9
10.6 Interface Unit IF-2500............... 10-18
10.7 GPS/BEACON
Antenna Distributor MD-GB2.... 10-22
APPENDIX
Menu Tree ......................................... AP-1
World Time Standards ....................... AP-3
Geodetic Chart List............................ AP-5
Loran C Chains.................................. AP-6
Decca Chains .................................... AP-7
Parts List ........................................... AP-8
Parts Location.................................... AP-9
Interface Documentation ................. AP-10