Tyco MX4428 - Manual (Page 83)

Document: LT0273 MX4428 MXP Engineering / Technical Manual
Event Log and Status at MX4428
Issue 1.5 24 March 2006 Page 6-3
6.2 FAULT AND ALARM EVENT LOG
The table below lists examples of event log items which are produced at the MX4428 panel.
Circuit / point event logging must be enabled to see the events listed below. Zone events are
not shown.
Event on MXP
Event Logged Event Logged on return to
normal
Database tx from F4000
to MXP RSP 1 DATABASE TX
START RSP 1 DATABASE TX
COMPLETE
Point Alarm CCT 1/1 ALARM
PNT 1/30 ALARM CCT 1/1 ALARM CLR
PNT 1/30 ALARM CLR
Point Fault CCT 1/1 FAULT
PNT 1/20 FAULT PNT 1/20 FAULT CLR
CCT 1/1 NORMAL
Point Pre-Alarm PNT 1/3 PRE-ALARM PNT 1/3 ALARM CLR
SNM800 wiring o/c or
s/c RLY 1/1 FAULT
PNT 1/26 SUPERVISION
FAULT PNT 1/26 NORMAL OFF
RLY 1/1 NORMAL
SNM800 Supply Fail RLY 1/1 FAULT
PNT 1/26 LOAD SUPPLY
FAIL PNT 1/26 NORMAL OFF
RLY 1/1 NORMAL
SNM800 / RIM800
checkback fail RLY 1/1 FAULT
PNT 1/24 CONTROL CB
FAIL PNT 1/24 CONTROL CB NML
(RIM800)
PNT 1/26 NORMAL ON (or OFF)
(SNM800)
RLY 1/1 NORMAL
DIM800 Supply Low CCT 1/1 FAULT
PNT 1/25 FAULT
PNT 1/25 LOAD SUPPLY
FAIL PNT 1/25 FAULT CLR
CCT 1/1 NORMAL
Point scan fail PNT 1/22 NODE FAIL
CCT 1/1 FAULT PNT 1/22 NODE FAIL CLR
CCT 1/1 NORMAL
Detector calibration fault CCT 1/1 FAULT
PNT 1/2 FAULT
PNT 1/2 PARAMETER
ERROR CCT 1/1 NORMAL
PNT 1/2 FAULT
Loop o/c RSP 1 LOOP OPEN
CIRCUIT RSP 1 LOOP OPEN CIRCUIT
CLEARED
Loop line A or B short or
overload RSP 1 LOOP SHORT
CIRCUIT RSP 1 LOOP SHORT CIRCUIT
CLEARED
Type Mismatch PNT 1/1 POINT TYPE
MISMATCH PNT 1/1 POINT TYPE OK
Foreign Device PNT 1/3 FOREIGN DEVICE (note- re-logged after DP command)
System Test or autotest
- device not normal at
start PNT 1/2 TEST START NOT NML
CCT 1/1 FAIL SELF TEST 3 1
System Test or autotest
- device alarm test fail PNT 1/1 ALARM TEST FAIL
CCT 1/1 FAIL SELF TEST 3 1
Zone alarm test device
fail PNT 1/1 ALARM TEST FAIL
Diagnostic Pollscan result -Correct point found P1/22 LINE 1 OK LINE 2 OK LED OFF
TYPE
OK
Diagnostics Pollscan result - point not found P1/100 LINE 1 FAULT LINE 2 FAULT LED
OFF TYPE OK
Diagnostic Pollscan result -Type mismatch P1/20 LINE 1 OK LINE 2 OK LED OFF
TYPE
BAD
Note “Type Mismatch” means a different device type was found at an address, from the type
programmed in the panel configuration for that address. An example of this would be a
MIM800 found at an address that is configured to have an 814PH. Refer to section 3.1.1 for
details of some device substitutions that are accepted without generating a fault.