Yamaha HTR-6090 - Manual (Page 101)

97
En
CUSTOMIZING THIS UNIT (MANUAL SETUP)
AD
V
ANCED
OPE
R
A
T
IO
N
Component interlace/progressive up-conversion
CMPNT I/P
Use this feature to activate or deactivate the analog
interlace/progressive conversion of the analog video
signals input at the composite video, S-video and
component video jacks so that the analog video signals
deinterlaced from 480i (NTSC)/576i (PAL) to 480p/576p
are output at the COMPONENT MONITOR OUT jacks.
Choices: ON, OFF
• Select “ON” to activate the analog interlace/
progressive up-conversion of the analog video signals.
• Select “OFF” to deactivate the analog interlace/
progressive up-conversion of the analog video signals.
• This menu item is not available and hence not visible in the
OSD if “V CONV.” is set to “OFF”.
• If your video monitor does not support analog video signals
with 480p/576p of resolution, the SET MENU items may not be
displayed on your video monitor when “CMPNT I/P” is set to
“ON”. Use “V-RESET” in “ADVANCED SETUP” to set the
“CMPNT I/P” parameter to the factory preset setting (see
page 119).
HDMI interlace/progressive up-conversion
HDMI I/P
Use this feature to activate or deactivate the HDMI
interlace/progressive up-conversion of the analog video
signals input at the composite video, S-video and
component video jacks so that the analog video signals
deinterlaced from 480i (NTSC)/576i (PAL) to 480p/576p
are output at the HDMI OUT jack.
Choices: ON, OFF
• Select “ON” to activate the HDMI interlace/
progressive up-conversion of the analog video signals.
• Select “OFF” to deactivate the HDMI interlace/
progressive up-conversion of the analog video signals.
• This menu item is not available and hence not visible in the
OSD if “V CONV.” is set to “OFF”.
• When analog video signals with 1080i or 720p of resolution are
up-converted to HDMI and output at the HDMI OUT jack, the
picture quality may worsen.
Short message display SHORT MESSAGE
Use this feature to activate or deactivate the short message
display function.
Choices: ON, OFF
• Select “ON” to activate the short message display
function. The contents of the front panel display appear
at the bottom of the screen each time you operate this
unit.
• Select “OFF” to deactivate the short message display
function.
The short message display does not appear in the following cases:
– when the component video signals with 480p/576p, 720p,
1080i or 1080p resolutions are input
– when HDMI video signals are input
On-screen display time ON SCREEN
Use this feature to set the amount of time to display the
XM Satellite Radio information or iPod menu in the OSD
after you perform a certain operation.
Choices: ALWAYS, 10SEC, 30SEC
• Select “ALWAYS” to display the OSD unceasingly
during an operation.
• Select “10SEC” to turn off the OSD 10 seconds after
you perform a certain operation.
• Select “30SEC” to turn off the OSD 30 seconds after
you perform a certain operation.
Front panel display scroll FL SCROLL
Use this feature to set whether to display the information
(such as song title or channel name) in the front panel
display in a continuous manner or by the first 14
alphanumeric characters after scrolling all characters once
when “XM” or “DOCK” is selected as the input source.
Choices: CONT, ONCE
• Select “CONT” to display the operation status in the
front panel display in a continuous manner.
• Select “ONCE” to display the operation status in the
front panel display by the first 14 alphanumeric
characters after scrolling all characters once.
Notes
Notes
Note
01EN_00_HTR-6090_U.book Page 97 Tuesday, June 27, 2006 6:40 PM