Yamaha HTR-6090 - Manual (Page 122)

118
En
ADVANCED SETUP
■ Speaker impedance
SPEAKER IMP.
Use this feature to set the speaker impedance of this unit
so that it matches that of your speakers.
Choices: 8
ΩMIN, 6ΩMIN
• Select “
8ΩMIN” to set the speaker impedance to 8 Ω .
• Select “6
ΩMIN” to set the speaker impedance to 6 Ω .
■ User presets
USER PRESET
Use this feature to reset all the parameters of this unit to
the initial factory settings (see page 130).
Choices: CANCEL, RESET
• Select “CANCEL” not to reset any parameters of this
unit.
• Select “RESET” to reset the parameters of this unit.
• This setting completely resets all the parameters of this unit
including the “SET MENU” parameters. However, the
advanced setup menu parameters will not be initialized.
• The initial factory settings are activated next time you turn on
this unit.
■ Remote sensor
REMOTE SENSOR
Use this feature to activate or deactivate the signal-
receiving capability of the remote control sensor on the
front panel of this unit.
Choices: ON, OFF
• Select “ON” if you want to activate the signal-
receiving capability of the remote control sensor.
• Select “OFF” if you want to deactivate the signal-
receiving capability of the remote control sensor.
We recommend setting the parameter to “ON” in most cases.
■ Wake on RS-232C access
WAKE ON
RS232C
Use this feature to set this unit to transmit data via the RS-
232C interface when this unit is in the standby mode.
Choices: YES, NO
Initial setting:
[U.S.A. and Canada models]: YES
[Other models]: NO
• Select “YES” to set this unit to transmit data via the
RS-232C interface.
• Select “NO” to set this unit not to transmit data via the
RS-232C interface.
■ Remote control AMP ID
RC AMP ID
Use this feature to set the AMP ID of this unit for remote
control recognition (see page 103).
Choices: ID1, ID2
• Select “ID1” when the remote control AMP ID library
code is set to “2001”.
• Select “ID2” when the remote control AMP ID library
code is set to “2002”.
You need to set the corresponding remote control AMP library
code for the remote control (see page 103).
■ Remote control TUNER ID
RC TUNER ID
Use this feature to set the TUNER ID of this unit for
remote control recognition (see page 121).
Choices: ID1, ID2
• Select “ID1” when the remote control TUNER ID
library code is set to “2602”.
• Select “ID2” when the remote control TUNER ID
library code is set to “2603”.
You need to set the corresponding remote control TUNER library
code for the remote control (see page 121).
■ Remote control XM ID
RC XM ID
Use this feature to set the XM ID of this unit for remote
control recognition (see page 121).
Choices: ID1, ID2
• Select “ID1” when the remote control XM ID library
code is set to “2604”.
• Select “ID2” when the remote control XM ID library
code is set to “2605”.
You need to set the corresponding remote control XM library
code for the remote control (see page 121).
SPEAKER
IMP.
Speaker Impedance level
8ΩMIN
Front
The impedance of each
speaker must be 8
Ω or
higher.
Center
The impedance of each
speaker must be 8
Ω or
higher.
Surround
Surround back
6ΩMIN
Front
The impedance of each
speaker must be 4
Ω or
higher.
Center
The impedance of each
speaker must be 6
Ω or
higher.
Surround
Surround back
Notes
Note
Note
Note
Note
01EN_00_HTR-6090_U.book Page 118 Tuesday, June 27, 2006 6:40 PM