Rainbow Electronics 71M6542G - Manual (Page 87)

v1.1 © 2008–2011 Teridian Semiconductor Corporation 87
There is no internal digital state that could deactivate the WDT. For debug purposes, however, the WDT
can be disabled by raising the ICE_E pin to 3.3 VDC.
In normal operation, the WDT is reset by periodically writing a one to the WD_RST control bit (I/O RAM
0x28B4[7]). The watchdog timer is also reset when the 71M654x wakes from LCD or SLP mode, and
when ICE_E = 1.
3.4 Wake Up Behavior
As described above, the part always wakes-up in MSN mode when system power is restored. As
described in
3.2 Battery Modes , transitions from both LCD and SLP mode to BRN mode can be initiated
by a wake-up timer timeout, when the pushbutton (PB) input is high, a high level on SEGDIO4,
SEGDIO52 or SEGDIO55, or by activity on the RX or OPT_RX pins.
3.4.1 Wake on Hardware Events
The following pin signal events wake the 71M654x from SLP or LCD mode: a high level on the PB pin, either
edge on the RX pin, a rising edge on the SEGDIO4 pin, a high level on the SEGDIO52 pin (71M6542F only),
or a high level on the SEGDIO55 pin or either edge on the OPT_RX pin. See
Table 69 for de-bounce details
on each pin and for further details on the OPT_RX/SEGDIO55 pin. The SEGDIO4, SEGDIO52 (71M6542F
only), and SEGDIO55 pins must be configured as DIO inputs and their wake enable (EW_x bits) must be
set. In SLP and LCD modes, the MPU is held in reset and cannot poll pins or react to interrupts. When
one of the hardware wake events occurs, the internal WAKE signal rises and within three CK32 cycles
the MPU begins to execute. The MPU can determine which one of the pins awakened it by checking the
WF_PB, WF_RX, WF_SEGDIO4, WF_DIO52 (71M6542F only), or WF_DIO55 flags (see
Table 69 ).
If the part is in SLP or LCD mode, it can be awakened by a high level on the PB pin. This pin is normally
pulled to GND and can be connected externally so it may be pulled high by a push button depression.
Some pins are de-bounced to reject EMI noise. Detection hardware ignores all transitions after the initial
transition.
Table 69 shows which pins are equipped with de-bounce circuitry.
Pins that do not have de-bounce circuits must still be high for at least 2 µs to be recognized.
The wake enable and flag bits are also shown in Table 69 . The wake flag bits are set by hardware when
the MPU wakes from a wake event. Note that the PB flag is set whenever the PB is pushed, even if the
part is already awake.
Table 71 lists the events that clear the WF flags.
In addition to push buttons and timers, the part can also reboot due to the RESET pin, the RESET bit (I/O
RAM 0x2200[3]), the WDT, the cold start detector, and E_RST. As seen in
Table 69 , each of these
mechanisms has a flag bit to alert the MPU to the source of the wakeup. If the wake-up is caused by
return of system power, there is no active WF flag and the VSTAT[2:0] field (SFR 0xF9[2:0]) indicate that
system power is stable.
Table 69: Wake Enables and Flag Bits
Wake Enable Wake Flag
De-bounce Description
Name Location Name Location
WAKE_ARM 28B2[5] WF_TMR 28B1[5] No Wake on Timer.
EW_PB 28B3[3] WF_PB 28B1[3] Yes Wake on PB*.
EW_RX 28B3[4] WF_RX 28B1[4] 2 µs Wake on either edge of RX.
EW_DIO4 28B3[2] WF_DIO4 28B1[2] 2 µs Wake on SEGDIO4.
EW_DIO52
†
28B3[1] WF_DIO52 28B1[1] Yes Wake on SEGDIO52*.
EW_DIO55 28B3[0] WF_DIO55 28B1[0] Yes
OPT_RXDIS = 1: Wake on DIO55*
with 64 ms de-bounce.
OPT_RXDIS = 0: Wake on either
edge of OPT_RX with 2 µs de-