GE Industrial Solutions AF-650 GP General Purpose Drive (460_575_690V 125HP and above) - Manual (Page 116)

Mains Supply 3 x 525- 690 VAC
AF-650 GP
900 HP 1000 HP 1200 HP 1250 HP 1350 HP
Heavy Duty/Light Duty* HD LD HD LD HD LD HD LD HD LD
Typical Shaft output at
550 V [kW]
500 560 560 670 670 750 750 850 850 1000
Typical Shaft output at
575 V [HP]
650 750 750 950 950 1050 1050 1150 1150 1350
Typical Shaft output at
690 V [kW]
630 710 710 800 800 900 900 1000 1000 1200
IP21/Nema 1 and IP54/
Nema 12 Drive Types
without/with options
cabinet
61/ 63 61/ 63 61/ 63 62/ 64 62/ 64
Output current
Continuous
(at 550 V) [A]
659 763 763 889 889 988 988 1108 1108 1317
Intermittent (60 sec
overload)
(at 550 V) [A]
989 839 1145 978 1334 1087 1482 1219 1662 1449
Continuous
(at 575/ 690 V) [A]
630 730 730 850 850 945 945 1060 1060 1260
Intermittent (60 sec
overload)
(at 575/ 690 V) [A]
945 803 1095 935 1275 1040 1418 1166 1590 1386
Continuous KVA
(at 550 V) [KVA]
628 727 727 847 847 941 941 1056 1056 1255
Continuous KVA
(at 575 V) [KVA]
627 727 727 847 847 941 941 1056 1056 1255
Continuous KVA
(at 690 V) [KVA]
753 872 872 1016 1016 1129 1129 1267 1267 1506
Max. input current
Continuous
(at 550 V ) [A]
642 743 743 866 866 962 962 1079 1079 1282
Continuous
(at 575 V) [A]
613 711 711 828 828 920 920 1032 1032 1227
Continuous
(at 690 V) [A]
613 711 711 828 828 920 920 1032 1032 1227
Max. cable size, motor
[mm
2 (AWG 2) )]
8x150
(8x300 mcm)
12x150
(12x300 mcm)
Max. cable size,mains
[mm
2 (AWG 2) )]
8x240
(8x500 mcm)
Max. cable size, load-
sharing [mm
2 (AWG 2) )]
4x120
(4x250 mcm)
Max. cable size, brake
[mm
2 (AWG 2) )
4x185
(4x350 mcm)
6x185
(6x350 mcm)
Max. external pre-fuses
[A]
1
1600 2000
Estimated power loss
at rated max. load [W]
4)
Weight,
Unit Size IP21, IP 54 [kg]
1004/ 1299 1004/ 1299 1004/ 1299 1246/ 1541 1246/ 1541
Weight, Rectifier Module
[kg]
102 102 102 136 136
Weight, Inverter Module
[kg]
102 102 136 102 102
Efficiency 4) 0.98
Output frequency 0-500 Hz
Heatsink overtemp. trip 85 °C
Power card ambient trip 68 °C
* Heavy Duty = 160% torque during 60 s, Light Duty = 110% torque during 60 s
1) For type of fuse see section Fuses.
2) American Wire Gauge.
3) Measured using 5 m screened motor cables at rated load and rated frequency.
4) The typical power loss is at nominal load conditions and expected to be within +/-15% (tolerence relates to variety in voltage and cable conditions).
Values are based on a typical motor efficiency (eff2/eff3 border line). Motors with lower efficiency will also add to the power loss in the frequency converter
and opposite.
If the switching frequency is increased compared to the default setting, the power losses may rise significantly.
Keypad and typical control card power consumptions are included. Further options and customer load may add up to 30W to the losses. (Though typical
only 4W extra for a fully loaded control card, or options for slot A or slot B, each).
Although measurements are made with state of the art equipment, some measurement inaccuracy must be allowed for (+/-5%).
AF-650 GP High Power Operating Instructions
115
5