Fire-Lite 411UDAC Fire Alarm Communicator - Manual (Page 51)

411UDAC Manual — P/N 51073:E 9/20/2013 51
Default Mode Modes of Operation
Service Terminal 1 Phone Number (101 - 120)
Addresses 100 - 119 are reserved for the Service Terminal Number 1 phone number. Factory
default is all 'F's. Valid entries are 0 - 9 plus A, B, C, D and E. Use 'F' to designate the end of the
phone number. See “Remote Site Upload/Download” on page 60 for additional information.
Ring Count on Primary Phone Line (121 - 122)
Use this address to designate the number of rings allowed on the primary phone line prior to
answering an incoming call from the Service Terminal. Factory default is '3' meaning the commu-
nicator will not answer an incoming call until 3 rings are detected. This entry may be programmed
up to a maximum of '25' rings. A setting of '00' prevents the communicator from answering incom-
ing calls.
FAX/Answer Machine, Primary Phone Line (123)
This entry is used when the primary phone line is being shared with a FAX, answering machine or
other device. Factory default is '0' for no sharing of the primary phone line. An entry of '1' indi-
cates that another device is sharing the primary phone line. The communicator will wait for three
consecutive calls from the Service Terminal spaced 30 seconds apart, before responding. Sharing
of phone lines requires the prior approval of the AHJ (Authority Having Jurisdiction).
Service Terminal 2 Phone Number (124 - 143)
Addresses 123 - 142 are reserved for the Service Terminal Number 2 phone number. Factory
default is all 'F's. Valid entries are 0 - 9 plus A, B, C, D and E. Use 'F' to designate the end of the
phone number. See “Remote Site Upload/Download” on page 60 for additional information.
Upload/Download Reports Sent to Secondary Central Station Phone #,
Backup or Always (144)
Leaving address 144 programmed to the factory default setting of '0' means that reports for request
for 'upload/download' and 'failed upload/download' will be sent to the secondary Central Station
phone number only if attempts to the primary Central Station phone number are unsuccessful. Pro-
gramming a '1' causes all reports to be transmitted to both primary and secondary phone numbers.
Programming a '2' causes reports to be sent to the first available receiver.
Do not alter entry while the communicator is active.
Programming Event Code Settings (145 - 312)
Event Code Settings, corresponding to the Formats selected for the Primary Central Station phone
number in address 20 and the Secondary Central Station phone number in address 50, are automat-
ically set to factory default values. Refer to Table 3.1, “Ademco Contact ID Format - Primary,” on
page 37, Table 3.2, “4+2 Standard and 4+2 Express Formats - Primary,” on page 38, and
Table 3.3, “All 3+1, 4+1 and 4+2 Expanded Formats - Primary,” on page 39 for format desig-
nated by address 20. Refer to Table 3.4, “Ademco Contact ID Format - Secondary,” on page 42,
Table 3.5, “4+2 Standard and 4+2 Express Formats - Secondary,” on page 43, and Table 3.6, “All
3+1, 4+1 and 4+2 Expanded Formats - Secondary,” on page 44 for format designated by address
50. The Event Code Settings can be altered. Consult your Central Station prior to changing the
event code settings.
3.5 Default Mode
To return all program entries, including the upload/download secret password and time, to their fac-
tory original settings, perform the following steps only when the system is idle (i.e. the communi-
cator is not active) and there are no active fire alarms or fire supervisories in the system:
Press the MODE key followed by the 4-digit code 3337 and press the [ENTER/STORE] key.
3337 spells DEFP (DEFault Programming) on a Touch-Tone
®
phone.