Fire-Lite 411UDAC Fire Alarm Communicator - Manual (Page 67)

411UDAC Manual — P/N 51073:E 9/20/2013 67
Digital Communicator Options Program Sheets Programming Sheets

78

79

80
Input Channel 4 Delay Timer. Enter 0 - 179 seconds delay. Factory default is '000' for no delay.
Does not delay Input Channels programmed for fire functions.

81
Touchtone/Rotary Select for Primary Phone. Enter '0' for touchtone dialing; '1' for rotary dialing.

82
Make/Break Ratio for Primary Phone. Enter '0' for 67/33 ratio; '1' for 62/38 ratio.

83
Touchtone/Rotary Select for Secondary Phone. Enter '0' for touchtone dialing; '1' for rotary dialing.

84
Make/Break Ratio for Secondary Phone. Enter '0' for 67/33 ratio; '1' for 62/38 ratio.

85
Output Relay #1 enable. Enter '1' to enable Relay #1; '0' to disable relay.

86
Output Relay #1 Function. Enter '0' for relay to activate on alarm; '1' host panel trouble; '2' DACT trouble; '3'
for latching fire supervisory; '4' for autoresettable fire supervisory; '7' (future use); '8' for total communication failure.

87
Output Relay #2 enable. Enter '1' to enable Relay #2; '0' to disable relay.

88
Output Relay #2 Function. Enter '0' for relay to activate on fire alarm; '1' host panel trouble; '2' for DACT
trouble; '3' for latching fire supervisory; '4' for autoresettable fire supervisory; '7' (future use); '8' total communication
failure.

89
Reserved for future use. Leave default setting of ‘0.’

90
Panel unlock. Enter ‘0’ for password unlock, ‘1’ for permanent unlock.

91
Alarm verification. Enter '0' for no verification; '1' for verification of all 4-wire smoke zones.

92
Silence inhibit. Enter '0' for no silence inhibit; '1' to inhibit silencing of NAC for one minute.

93
Autosilence. Enter '0' for no autosilence; '1' for 5 minute autosilence; '2' for 10 minutes; '3' for 15 minutes; '4'
for 20 minutes; '5' for 25 minutes; '6' for 30 minutes.

94
Restoral method. Enter '0' for Typical restoral method; '1' for Conditional Restoral Method #1; '2' for Condi-
tional Restoral Method #2.

95
Coding, Notification Appliance Circuit. Enter ‘0’ for no coding (steady); ‘1’ for Temporal coding.

96
Trouble Call Limit - Dialer Runaway Prevention Feature. Enter a '0' to disable this feature; '1' to enable Trou-
ble Call Limit. Factory default is '0' for disabled.

97

98

99

100
Panel Identification Number.

101

102

103

104

105

106

107

108

109

110

111

112

113

114

115

116

117

118

119

120
Addresses 101 to 120 store the Service Terminal 1 Phone Number. Valid entries are 0 - 9 and A - E.
'F' designates the end of the phone number.

121

122
Ring Count on Primary Phone Line. Enter number of rings prior to panel answering call. Valid entries
are 00 to 25 (00 = no answer). Factory default is 03.

123
FAX/Answer Machine, Primary Phone Line. Enter '0' for no sharing of phone line; '1' for sharing.

124

125

126

127

128

129

130

131

132

133

134

135

136

137

138

139

140

141

142

143
Addresses 124 to 143 store the Service Terminal 2 Phone Number. Valid entries are 0-9 and A-E.
'F' designates the end of the phone number.

144
Upload/Download Backup Reporting. Enter '0' for Upload/Download reports to go to the Secondary Central
Station Phone Number on backup only; '1' for Upload/Download reports to always go to the Secondary; '2' for
Upload/Download reports to go to the first available Central Station phone number.