H3C Technologies H3C S10500 Series Switches User Manual
Page 102
93
# Cancel the physical state change suppression interval setting on GigabitEthernet 1/0/1 and
GigabitEthernet 1/0/2, and disable the spanning tree feature. Configure the two ports as trunk ports,
and assign them to VLANs 1 through 30.
[DeviceA] interface gigabitethernet 1/0/1
[DeviceA-GigabitEthernet1/0/1] undo link-delay
[DeviceA-GigabitEthernet1/0/1] undo stp enable
[DeviceA-GigabitEthernet1/0/1] port link-type trunk
[DeviceA-GigabitEthernet1/0/1] port trunk permit vlan 1 to 30
[DeviceA-GigabitEthernet1/0/1] quit
[DeviceA] interface gigabitethernet 1/0/2
[DeviceA-GigabitEthernet1/0/2] undo link-delay
[DeviceA-GigabitEthernet1/0/2] undo stp enable
[DeviceA-GigabitEthernet1/0/2] port link-type trunk
[DeviceA-GigabitEthernet1/0/2] port trunk permit vlan 1 to 30
[DeviceA-GigabitEthernet1/0/2] quit
# Create RRPP domain 1. Configure VLAN 4092 as the primary VLAN of RPPP domain 1, and configure
the VLANs mapped to MSTI 1 as the protected VLANs of RRPP domain 1.
[DeviceA] rrpp domain 1
[DeviceA-rrpp-domain1] control-vlan 4092
[DeviceA-rrpp-domain1] protected-vlan reference-instance 1
# Configure Device A as the master node of the primary ring Ring 1, with GigabitEthernet 1/0/1 as the
primary port and GigabitEthernet 1/0/2 as the secondary port, and enable Ring 1.
[DeviceA-rrpp-domain1] ring 1 node-mode master primary-port gigabitethernet 1/0/1
secondary-port gigabitethernet 1/0/2 level 0
[DeviceA-rrpp-domain1] ring 1 enable
# Enable fast detection, and set the Fast-Fail timer and Fast-Hello timer to 300 milliseconds and 100
milliseconds respectively. (Set the Fast-Fail timer equal to or greater than three times the Fast-Hello timer
value; otherwise, the configuration cannot succeed.)
[DeviceA-rrpp-domain1] fast-detection enable
[DeviceA-rrpp-domain1] timer fast-hello-timer 100
[DeviceA-rrpp-domain1] timer fast-fail-timer 300
[DeviceA-rrpp-domain1] quit
# Enable the RRPP protocol.
[DeviceA] rrpp enable
2.
Configure Device B.
# Create VLAN 4092 and VLAN 4093.
<DeviceB> system-view
[DeviceB] vlan 4092 to 4093
# Cancel the physical state change suppression interval setting on GigabitEthernet 1/0/1 and
GigabitEthernet 1/0/2, and disable the spanning tree feature. Configure the two ports as trunk ports,
and assign them to VLANs 1 through 30, VLAN 4092, and VLAN 4093.
[DeviceB] interface gigabitethernet 1/0/1
[DeviceB-GigabitEthernet1/0/1] undo link-delay
[DeviceB-GigabitEthernet1/0/1] undo stp enable
[DeviceB-GigabitEthernet1/0/1] port link-type trunk
[DeviceB-GigabitEthernet1/0/1] port trunk permit vlan 1 to 30 4092 4093
[DeviceB-GigabitEthernet1/0/1] quit