H3C Technologies H3C S10500 Series Switches User Manual

Page 131

Advertising

122

# Create VLANs 1 through 30.

<DeviceA> system-view

[DeviceA] vlan 1 to 30

# Configure GigabitEthernet 1/0/1 and GigabitEthernet 1/0/2 as trunk ports, assign them to VLANs
1 through 30, and enable flush message receiving on them.

[DeviceA] interface gigabitethernet 1/0/1

[DeviceA-GigabitEthernet1/0/1] port link-type trunk

[DeviceA-GigabitEthernet1/0/1] port trunk permit vlan 1 to 30

[DeviceA-GigabitEthernet1/0/1] smart-link flush enable

[DeviceA-GigabitEthernet1/0/1] quit

[DeviceA] interface gigabitethernet 1/0/2

[DeviceA-GigabitEthernet1/0/2] port link-type trunk

[DeviceA-GigabitEthernet1/0/2] port trunk permit vlan 1 to 30

[DeviceA-GigabitEthernet1/0/2] smart-link flush enable

[DeviceA-GigabitEthernet1/0/2] quit

Configure Device B.

# Create VLANs 1 through 30.

<DeviceB> system-view

[DeviceB] vlan 1 to 30

# Configure GigabitEthernet 1/0/1 as a trunk port, assign it to VLANs 1 through 30, and enable flush

message receiving on it.

[DeviceB] interface gigabitethernet 1/0/1

[DeviceB-GigabitEthernet1/0/1] port link-type trunk

[DeviceB-GigabitEthernet1/0/1] port trunk permit vlan 1 to 30

[DeviceB-GigabitEthernet1/0/1] smart-link flush enable

[DeviceB-GigabitEthernet1/0/1] quit

# Configure GigabitEthernet 1/0/2 as a trunk port, assign it to VLANs 1 through 30, disable the

spanning tree feature, and enable flush message receiving on it.

[DeviceB] interface gigabitethernet 1/0/2

[DeviceB-GigabitEthernet1/0/2] port link-type trunk

[DeviceB-GigabitEthernet1/0/2] port trunk permit vlan 1 to 30

[DeviceB-GigabitEthernet1/0/2] undo stp enable

[DeviceB-GigabitEthernet1/0/2] smart-link flush enable

[DeviceB-GigabitEthernet1/0/2] quit

# Create monitor link group 1, and then configure GigabitEthernet 1/0/1 as an uplink port and
GigabitEthernet 1/0/2 as a downlink port for monitor link group 1.

[DeviceB] monitor-link group 1

[DeviceB-mtlk-group1] port gigabitethernet 1/0/1 uplink

[DeviceB-mtlk-group1] port gigabitethernet 1/0/2 downlink

[DeviceB-mtlk-group1] quit

Configure Device D.

# Create VLANs 1 through 30.

<DeviceD> system-view

[DeviceD] vlan 1 to 30

# Configure GigabitEthernet 1/0/1 as a trunk port, assign it to VLANs 1 through 30, and enable flush
message receiving on it.

Advertising

This manual is related to the following products:

H3C S5800 Series Switches, H3C S5820X Series Switches, H3C WX3000E Series Wireless Switches, H3C SecPath F1000-E, H3C SecPath F5000-A5 Firewall, H3C SecPath F1000-A-EI, H3C SecPath F1000-E-SI, H3C SecPath F1000-S-AI, H3C SecPath F5000-S Firewall, H3C SecPath F5000-C Firewall, H3C SecPath F100-C-SI, H3C SecPath F1000-C-SI, H3C SecPath F100-A-SI, H3C SecBlade FW Cards, H3C SecBlade FW Enhanced Cards, H3C SecPath U200-A U200-M U200-S, H3C SecPath U200-CA U200-CM U200-CS

Popular Brands

Popular manuals