H3C Technologies H3C S10500 Series Switches User Manual

Page 103

Advertising

[DeviceB] interface gigabitethernet 1/0/2

[DeviceB-GigabitEthernet1/0/2] undo link-delay

[DeviceB-GigabitEthernet1/0/2] undo stp enable

[DeviceB-GigabitEthernet1/0/2] port link-type trunk

[DeviceB-GigabitEthernet1/0/2] port trunk permit vlan 1 to 30 4092 4093

Configure Device C.

# Create VLAN 4092 and VLAN 4093.

<DeviceC> system-view

[DeviceC] vlan 4092 to 4093

# Cancel the physical state change suppression interval setting on GigabitEthernet 1/0/1 and
GigabitEthernet 1/0/2, and disable the spanning tree feature. Configure the two ports as trunk ports,

and assign them to VLANs 1 through 30, VLAN 4092, and VLAN 4093.

[DeviceC] interface gigabitethernet 1/0/1

[DeviceC-GigabitEthernet1/0/1] undo link-delay

[DeviceC-GigabitEthernet1/0/1] undo stp enable

[DeviceC-GigabitEthernet1/0/1] port link-type trunk

[DeviceC-GigabitEthernet1/0/1] port trunk permit vlan 1 to 30 4092 4093

[DeviceC-GigabitEthernet1/0/1] quit

[DeviceC] interface gigabitethernet 1/0/2

[DeviceC-GigabitEthernet1/0/2] undo link-delay

[DeviceC-GigabitEthernet1/0/2] undo stp enable

[DeviceC-GigabitEthernet1/0/2] port link-type trunk

[DeviceC-GigabitEthernet1/0/2] port trunk permit vlan 1 to 30 4092 4093

Configure Device D.

# Create VLANs 1 through 30, map these VLANs to MSTI 1, and activate the MST region configuration.

<DeviceD> system-view

[DeviceD] vlan 1 to 30

[DeviceD] stp region-configuration

[DeviceD-mst-region] instance 1 vlan 1 to 30

[DeviceD-mst-region] active region-configuration

[DeviceD-mst-region] quit

# Cancel the physical state change suppression interval setting on GigabitEthernet 1/0/1 and

GigabitEthernet 1/0/2, and disable the spanning tree feature. Configure the two ports as trunk ports,
and assign them to VLANs 1 through 30.

[DeviceD] interface gigabitethernet 1/0/1

[DeviceD-GigabitEthernet1/0/1] undo link-delay

[DeviceD-GigabitEthernet1/0/1] undo stp enable

[DeviceD-GigabitEthernet1/0/1] port link-type trunk

[DeviceD-GigabitEthernet1/0/1] port trunk permit vlan 1 to 30

[DeviceD-GigabitEthernet1/0/1] quit

[DeviceD] interface gigabitethernet 1/0/2

[DeviceD-GigabitEthernet1/0/2] undo link-delay

[DeviceD-GigabitEthernet1/0/2] undo stp enable

[DeviceD-GigabitEthernet1/0/2] port link-type trunk

[DeviceD-GigabitEthernet1/0/2] port trunk permit vlan 1 to 30

[DeviceD-GigabitEthernet1/0/2] quit

Advertising

This manual is related to the following products:

H3C S5800 Series Switches, H3C S5820X Series Switches, H3C WX3000E Series Wireless Switches, H3C SecPath F1000-E, H3C SecPath F5000-A5 Firewall, H3C SecPath F1000-A-EI, H3C SecPath F1000-E-SI, H3C SecPath F1000-S-AI, H3C SecPath F5000-S Firewall, H3C SecPath F5000-C Firewall, H3C SecPath F100-C-SI, H3C SecPath F1000-C-SI, H3C SecPath F100-A-SI, H3C SecBlade FW Cards, H3C SecBlade FW Enhanced Cards, H3C SecPath U200-A U200-M U200-S, H3C SecPath U200-CA U200-CM U200-CS

Popular Brands

Popular manuals