H3C Technologies H3C S10500 Series Switches User Manual

Page 86

Advertising
background image

77

# Configure Device A as the edge node of subring 2, with GigabitEthernet 1/0/4 as the edge port, and

enable subring 2.

[DeviceA-rrpp-domain1] ring 2 node-mode edge edge-port gigabitethernet 1/0/4

[DeviceA-rrpp-domain1] ring 2 enable

# Configure Device A as the edge node of subring 3, with GigabitEthernet 1/0/3 as the edge port, and
enable subring 3.

[DeviceA-rrpp-domain1] ring 3 node-mode edge edge-port gigabitethernet 1/0/3

[DeviceA-rrpp-domain1] ring 3 enable

[DeviceA-rrpp-domain1] quit

# Enable RRPP.

[DeviceA] rrpp enable

2.

Configure Device B.

# Create VLANs 1 through 30, map these VLANs to MSTI 1, and activate the MST region configuration.

<DeviceB> system-view

[DeviceB] vlan 1 to 30

[DeviceB] stp region-configuration

[DeviceB-mst-region] instance 1 vlan 1 to 30

[DeviceB-mst-region] active region-configuration

[DeviceB-mst-region] quit

# Cancel the physical state change suppression interval setting on GigabitEthernet 1/0/1 through
GigabitEthernet 1/0/4, and disable the spanning tree feature. Configure the four ports as trunk ports,

and assign them to VLANs 1 through 30.

[DeviceB] interface gigabitethernet 1/0/1

[DeviceB-GigabitEthernet1/0/1] undo link-delay

[DeviceB-GigabitEthernet1/0/1] undo stp enable

[DeviceB-GigabitEthernet1/0/1] port link-type trunk

[DeviceB-GigabitEthernet1/0/1] port trunk permit vlan 1 to 30

[DeviceB-GigabitEthernet1/0/1] quit

[DeviceB] interface gigabitethernet 1/0/2

[DeviceB-GigabitEthernet1/0/2] undo link-delay

[DeviceB-GigabitEthernet1/0/2] undo stp enable

[DeviceB-GigabitEthernet1/0/2] port link-type trunk

[DeviceB-GigabitEthernet1/0/2] port trunk permit vlan 1 to 30

[DeviceB-GigabitEthernet1/0/2] quit

[DeviceB] interface gigabitethernet 1/0/3

[DeviceB-GigabitEthernet1/0/3] undo link-delay

[DeviceB-GigabitEthernet1/0/3] undo stp enable

[DeviceB-GigabitEthernet1/0/3] port link-type trunk

[DeviceB-GigabitEthernet1/0/3] port trunk permit vlan 1 to 30

[DeviceB-GigabitEthernet1/0/3] quit

[DeviceB] interface gigabitethernet 1/0/4

[DeviceB-GigabitEthernet1/0/4] undo link-delay

[DeviceB-GigabitEthernet1/0/4] undo stp enable

[DeviceB-GigabitEthernet1/0/4] port link-type trunk

[DeviceB-GigabitEthernet1/0/4] port trunk permit vlan 1 to 30

[DeviceB-GigabitEthernet1/0/4] quit

Advertising
This manual is related to the following products:

H3C S5800 Series Switches, H3C S5820X Series Switches, H3C WX3000E Series Wireless Switches, H3C SecPath F1000-E, H3C SecPath F5000-A5 Firewall, H3C SecPath F1000-A-EI, H3C SecPath F1000-E-SI, H3C SecPath F1000-S-AI, H3C SecPath F5000-S Firewall, H3C SecPath F5000-C Firewall, H3C SecPath F100-C-SI, H3C SecPath F1000-C-SI, H3C SecPath F100-A-SI, H3C SecBlade FW Cards, H3C SecBlade FW Enhanced Cards, H3C SecPath U200-A U200-M U200-S, H3C SecPath U200-CA U200-CM U200-CS

Popular Brands
Popular manuals