Roland V-60HD Multi-Format HD Video Switcher and UVC-01 USB Video Capture Kit - Manual (Page 35)

35
Other Features
Preventing Unintended Operation
(Panel Lock)
This locks operation of buttons and knobs to prevent unintended
operation of the V-60HD.
1.
Select the [MENU] button 0 “SYSTEM” 0 “PANEL LOCK.”
2.
With the cursor positioned at “ENTER,” press the [VALUE] knob.
The PANEL LOCK menu appears.
3.
Select a target for panel lock, then use the [VALUE] knob to
specify whether panel lock is applied (ON) or not applied
(OFF).
You can select the following menu items as targets for panel lock.
Menu item Target of panel lock
ALL SW & VOLUME All buttons and knobs
MENU SW + EXIT SW [MENU] and [EXIT] buttons
VALUE ENCODER [VALUE] knob
PGM/A 1–8 SW PGM/A bus cross-point [1]–[8] buttons
PST/B 1–8 SW PST/B bus cross-point [1]–[8] buttons
AUX/MEMORY 1–8 SW AUX/MEMORY buttons (All)
MODE SW [MODE] button
CUT SW + AUTO SW [CUT] and [AUTO] buttons
VIDEO FADER Video fader
OUTPUT FADE SW [OUTPUT FADE] button
DSK ON/OFF SW [DSK] button
COMPOSITION BLOCK
[H/PGM-CTR] and [V/PST-CTR] knobs
[PinP 1], [PinP 2], and [SPLIT] buttons
TRANSITION BLOCK
[MIX], [WIPE 1], and [WIPE 2] buttons
[TIME] knob
DSK BLOCK
[LEVEL] and [GAIN] knobs
[PVW] button
AUDIO IN 1–6 VOLUME AUDIO INPUT LEVEL knobs (All)
AUTO MIXING SW [AUTO MIXING] button
MASTER OUTPUT VOLUME [MASTER OUTPUT] knob
4.
Press the [VALUE] knob to apply the setting.
Repeat steps 3 and 4 as needed.
5.
Press the [MENU] button to quit the menu.
6.
Press and hold the [EXIT] button and the [MENU] button at
the same time (for 3 seconds or longer).
The message “PANEL LOCKED” is displayed,
and panel lock is turned on. The button and
controls that you set to applied (ON) in step
3 are locked.
7.
To turn off panel lock, again press and hold the [EXIT] button
and the [MENU] button at the same time (for 3 seconds or
longer).
The message “LOCK RELEASED” is displayed, and panel lock is
turned off.
Operating the V-60HD by Remote Control
You can operate the V-60HD remotely from an external device.
Using the dedicated V-60HD RCS program
You can connect the V-60HD to a computer via a LAN or RS-232,
and use dedicated program V-60HD RCS to operate the unit by
remote control.
For more information about operation methods, refer to the
owner’s manual included with V-60HD RCS.
RS-232
LAN
V-60HD RCS can be downloaded from the following Roland website.
https://proav.roland.com/
Using RS-232/LAN/GPI
You can operate the V-60HD remotely from an external device by
means of RS-232/LAN (CONTROL port)/GPI.
For the specifications of the RS-232 connector and the TALLY/
GPI connector and for more information on operating the unit
remotely, refer to the Reference Manual (PDF), available for
download at the Roland website shown above.
Outputting a Tally Signal
You can output a tally signal from the TALLY/GPI connector.
A tally signal is output from the connector pin corresponding to
the video channel being output, also including video composition
and transition effects.
For the specifications of the TALLY/GPI connector, refer to the
Reference Manual (PDF), available for download at the Roland
website shown above.
Using Smart Tally
Roland’s unique and proprietary wireless tally system uses a
wireless LAN router connected to the V-60HD to send tally
information to iOS or Android devices on the network.
For more information about operation methods, refer to the
“Using Smart Tally” (PDF), available for download at the Roland
website shown above.