Panasonic WJ-SX 150A - Manual (Page 59)

62
● Alarm Settings
The operation parameters when an alarm is input to the unit
are configurable.
• Alarm mode: The operation mode activated along with
an alarm input is configurable. Sequence mode or hold
mode is selectable. Alarm mode can be set to OFF
when not using it.
• Alarm event: The sequence number or spot camera is
selectable for the alarm event.
• Alarm input (Alarm port): The alarm polarity (N. O. or N.
C.) is assignable to each alarm input terminal.
• It is also selectable whether to activate the recording
and sequence/spot image monitoring when an alarm
signal is input to the unit. Alarm recording without the
sequence/spot image monitoring is also available.
● Operator Settings
If you control this unit with a terminal-mode system con-
troller, your operator information, controllable monitors and
auto log-in/log-out will be registrable and configurable.
• Operator registration: Up to 16 operators are available.
ID and password for operator identification are config-
urable. Level and priority can be assigned to each
operator. Each camera's control coverage is also con-
figurable.
• Level table: Restriction level for each password is cus-
tomizable.
• Monitor select (Monitor selection): Controllable monitor
can be assigned to each controller.
• Auto login/logout (Auto log-in/log-out): Auto log-in/log-
out is configurable for each controller.
Notes:
• These settings (except Operator registration) are con-
figurable only through WJ-SX150A Administrator
Console. Operator registration is configurable through
SETUP MENU and WJ-SX150A Administrator Console.
• When you control the unit with a PS·Data system con-
troller, the above settings will be invalid. Refer to the
system controller's operating instructions.
● System Settings
SETUP MENU can configure the clock (time and date),
cable compensation and camera title.
Besides these settings, WJ-SX150A Administrator Console
can select the data ports' baud rates.
• Clock (Time and date): The unit's time and date are
configurable.
• Cable compensation: Cable compensation type is
selectable depending on the distance between a cam-
era and the unit. It is also possible to determine whether
to send the VD2 timing pulse or control data with the
camera output signals.
• Camera title: Camera title is configurable to identify the
camera images on the monitor. WJ-SX150A
Administrator Console can configure the camera title
including original characters.
• Data port: Usually, the ports DATA 1 to 3 connect to the
terminal-mode system controllers. RS-485 cameras will
be connectable with the data port configurations
through WJ-SX150A Administrator Console and SETUP
MENU.
When you use the system controllers via the PS·Data
protocol, you need to configure the DATA 4 port setting
through SX150A Admin Console or SETUP MENU.
• Recorder: The type and unit address of the recorder
are configurable.
• Multiplxer: The parameters of the recorder mode are
configurable. You can set the alarm and normal record-
ing rate. You can also activate/deactivate dynamic
recording, dummy black, and "CAMSW LOSS Rn” indi-
cation. (Rn is a recorder number.)
• Mux camera (Multiplexer) title: Camera titles which are
displayed with multiscreen segments are configurable.
● Setup File Operation
WJ-SX150A Administrator Console can send a configura-
tion file from the PC to this unit. The utility can also send the
file from the unit to the PC for configuration.
• Put a file to SX150A: A configuration data is sent from
the PC to the unit.
• Get a configuration data from SX150A: A configuration
data is sent from the unit to the PC.
• Select setup data file: A configuration data is selected
when sending it from the PC to the unit (or from the unit
to the PC.)
Note: These settings are configurable only through WJ-
SX150A Administrator Console.
● WJ-SX150A Administrator Console
Configuration
The PC-related settings are configurable.
• Account Manager: WJ-SX150A Administrator Console
operators are registrable and changeable.
• Communication (Serial) port: PC's usable communica-
tion port number and its baud rate (communication
speed) are configurable.
MUX
MUX