Camera/data1 – 4 port, Compensation/vd2/data – Panasonic WJ-SX 150A User Manual
Page 71
74
SWITCHER:
Select a unit (SLAVE1 to 4 and MASTER*) to
configure the parameters.
* In normal connection, only MASTER is displayed.
CAM:
This stands for a camera channel of the unit.
LCN:
This stands for a logical camera number. 1 to 99 is
selectable.
COMP:
This stands for cable compensation. Select the
desired setting according to the cable length.
S:
Less than 400 m (1 300 ft)
M:
400 m (1 300 ft) to 700 m (2 300 ft)
L:
700 m (2 300 ft) to 900 m (3 000 ft)
Refer to p. 36 for available cables.
The factory default setting is S.
VD2:
To send the VD2 timing pulse with the camera output
signal, select ON. Not to send the VD2 timing pulse with
the camera output signal, select OFF. The factory
default setting is ON.
DATA:
To send the control data with the camera output sig-
nal, select ON. Not to send the control data with the
camera output signal, select OFF. The factory default
setting is ON.
* The available camera numbers will differ depending on
the total number of matrix switchers.
Notes:
• When moving the joystick to ▼ at the bottom of COM-
PENSATION/VD2/DATA, the monitor will display 2 of 2.
• When moving the joystick to ▲ at the bottom of COM-
PENSATION/VD2/DATA, the monitor will display 1 of 2.
• Camera channels of the Master unit which connect
Slave units are displayed as a space. You cannot con-
figure the parameters.
• CAMERA/DATA1 – 4 PORT
This menu links to the submenu.
Move the cursor and press the CAM (SET) button to go into
the menu.
740 CAMERA/DATA1-4 PORT will appear on the monitor.
Setting for normal connection
740 CAMERA/DATA1-4 PORT
SWITCHER=SLAVE1(1 of 5)
PORT MODE SPEED
CAMERA CAMERA 19200bps
DATA1 CAMERA 19200bps
DATA2 CAMERA 19200bps
DATA3 CAMERA 19200bps
DATA4 MASTER-SLAVE 38400bps
HDR HDR 9600bps
SERIAL -- 38400bps
When Master, Slave 1 to 3 are connected
CAM
1
2
3
4
5
6
7
8
9 10 11 12 13 14 15 16
Slave 1
1
2
3
4
5
6
7
8
9 10 11 12 13 14 15 16
Slave 2 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
Slave 3 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48
Master - - - - - - - - - - - - - - - - - - - - - - - - 49 50 51 52
CAM
1
2
3
4
5
6
7
8
9 10 11 12 13 14 15 16
Slave 1
1
2
3
4
5
6
7
8
9 10 11 12 13 14 15 16
Slave 2 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
Slave 3 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48
Slave 4 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64
Master - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
When Master, Slave 1 to 4 are connected
Notes:
• When you select logical camera numbers, the setting
will be automatically activated in other menus.
• Camera channels of the Master unit which connect
Slave units are displayed as a space. You cannot con-
figure the parameters.
• You can select a logical camera number for only one
channel. When you enter the same number second
time, the newer is activated, but the older will be
changed to a space.
• COMPENSATION/VD2/DATA
This menu links to the submenu.
Move the cursor and press the CAM (SET) button to go into
the menu.
730 COMPENSATION/VD2/DATA will appear on the moni-
tor.
730 COMPENSATION/VD2/DATA 1 of 2
SWITCHER=SLAVE1(1 of 4)
CAM LCN COMP VD2 DATA
1 1 S ON ON
2 2 S ON ON
3 3 S ON ON
4 4 S ON ON
5 5 S ON ON
6 6 S ON ON
7 7 S ON ON
8 8 S ON ON
LCN:LOGICAL CAMERA NUMBER
730 COMPENSATION/VD2/DATA 2 of 2
SWITCHER=SLAVE1(1 of 4)
CAM LCN COMP VD2 DATA
9 9 S ON ON
10 10 S ON ON
11 11 S ON ON
12 12 S ON ON
13 13 S ON ON
14 14 S ON ON
15 15 S ON ON
16 16 S ON ON
LCN:LOGICAL CAMERA NUMBER
740 CAMERA/DATA1-4 PORT
SWITCHER=MASTER(1 of 1)
PORT MODE SPEED
CAMERA CAMERA 19200bps
DATA1 TERMINAL-K1 9600bps
DATA2 TERMINAL-K2 9600bps
DATA3 TERMINAL-K3 9600bps
DATA4 PS-DATA 9600bps
HDR HDR 9600bps
SERIAL PC 38400bps