Yokogawa AXFA14G/C - Manual (Page 47)

IM 01E20F02-01E 6-4
Table 6.2 Status of each parameter in warning mode
Warning 80:Adhesion Wng Good (NC);
Maintenance
required, ok Good (NC);
Maintenance
required, ok Good (NC);
Maintenance
required, ok Good (NC);
Maintenance
required, ok
81:Insu-Brk Wng
Good (NC);
Maintenance
required, ok Good (NC);
Maintenance
required, ok Good (NC);
Maintenance
required, ok Good (NC);
Maintenance
required, ok Good (NC);
Maintenance
required, ok
82:Auto Zero Wng Uncertain;
Non specific,
ok Uncertain;
Non specific,
ok Uncertain;
Non specific,
ok Uncertain;
Non specific,
ok Uncertain;
Non specific,
ok Uncertain;
Non specific,
ok Uncertain;
Non specific,
ok Uncertain;
Non specific,
ok Uncertain;
Non specific,
ok
84:Disp Over Wng – – – – – – – – –
85:FLow Vel Over Uncertain;
Non specific,
Low/High limt. Uncertain;
Non specific,
Low/High limt. Uncertain;
Non specific,
Low/High limt. Uncertain;
Non specific,
Low/High limt. Uncertain;
Non specific,
Low/High limt. Uncertain;
Non specific,
Low/High limt. Uncertain;
Non specific,
Low/High limt. Uncertain;
Non specific,
Low/High limt. Uncertain;
Non specific,
Low/High limt.
140:Sim. Jmpr On – – – – – – –
141:PB Sim.
enabled (Note1) – – – – – – –
142:TB VF Sim.
enabled (Note1) – – – – – – –
143:AI Sim.
enabled (Note1) Depend on
SIMULATE.Status Depend on
SIMULATE.Status Depend on
SIMULATE.Status – – –
– –
90:Display Sw – – – – – – – – –
– –
– –
– – –
144:Total1 Sim.
enabled (Note1) – – – TOT1: Depend on
SIMULATE.
Status
TOT2: –
TOT3: –
– – –
145:Total2 Sim.
enabled (Note1) – – – TOT1: –
TOT2: Depend on
SIMULATE.
Status
TOT3: –
– – –
146:Total3 Sim.
enabled (Note1) – – – TOT1: –
TOT2: –
TOT3: Depend on
SIMULATE.
Status
TOT1: Depend on
SIMULATE.
Status
TOT2: –
TOT3: –
TOT1: –
TOT2: Depend on
SIMULATE.
Status
TOT3: –
TOT1: –
TOT2: –
TOT3: Depend on
SIMULATE.
Status
TOT1: Depend on
SIMULATE.
Status
TOT2: –
TOT3: –
TOT1: –
TOT2: Depend on
SIMULATE.
Status
TOT3: –
TOT1: –
TOT2: –
TOT3: Depend on
SIMULATE.
Status
– – –
147:DI1 Sim.
enabled (Note1) – – – – DI1: Depend on
SIMULATE.
Status
DI2: –
DI1: Depend on
SIMULATE.
Status
DI2: –
DI1: Depend on
SIMULATE.
Status
DI2: –
148:DI2 Sim.
enabled (Note1) – – – – DI1: –
DI2: Depend on
SIMULATE.
Status
DI1: –
DI2: Depend on
SIMULATE.
Status
DI1: –
DI2: Depend on
SIMULATE.
Status
150:AI FB Man
Mode – – – – – – –
151:Total1 FB Man
Mode – – – – – – –
152:Total2 FB Man
Mode – – – – – – –
153:Total3 FB Man
Mode – – – – – – –
154:DI1 FB Man
Mode – – – – – – –
155:DI2 FB Man
Mode
Note1: Make it the condition that the hardware simulation jumper is ON.
– – –
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
– – – – –
Category Warning
FSAFE_TYPE = 0
AI Block
FSAFE_TYPE = 1 FSAFE_TYPE = 2 FAIL_TOT = 0 FAIL_TOT = 1 FAIL_TOT = 2
TOT Block
FSAFE_TYPE = 0
DI Block
FSAFE_TYPE = 1 FSAFE_TYPE = 2