NORD Drivesystems BU0505 - Manual (Page 132)

SK 54xE – Users Manual for Frequency Inverters
132 BU 0505 GB-1013
P543 [-01]
...
[-05]
Bus actual value
(Bus – Actual value)
S P
0 ... 57
{ [-01] = 1 }
{ [-02] = 4 }
{ [-03] = 9 }
{ [-04] = 0 }
{ [-05] = 0 }
In this parameter the return value for bus actuation can be selected.
NOTE: The actual values 4 and 5 must be supported by the relevant bus module. For
further details please refer to the manual for the frequency inverter (P418, P543),
the relevant BUS operating instructions or the manuals BU 0510 / BU0550.
[-01] = Bus - Actual value 1 [-02] = Bus - Actual value 2 [-03] = Bus - Actual value 3
[-04] = Bus - Actual value 4 [-05] = Bus - Actual value 5
Pos : 304 /Anleit ungen/5. / 6. Parametrier ung [BU 0500 / BU 0200]/ Par ameter/ P500-P599/ Paramet er P543 - Bus- Is t wer te, Ei nst ellungen [ SK 5xxE] @ 2\ mod_1354267251544_388.doc x @ 51871 @ @ 1
0 = Off 13 = ... 16 Reserved
1 = Actual frequency 17 = Value analog input 1
2 = Actual speed 18 = Value analog input 2
3 = Current 19 = Setpoint frequency master
value(P503)
4 = Torque current (100% = P112) 20 = Setpoint frequency master value after
ramp "Setpoint frequency master
value after ramp"
5 = Digital IO status
5
21 = Act. freq. without slip master value
"Actual frequency without slip master
value"
6 = ... 7 Reserved 22 = Speed encoder (only possible with
SK 520E and encoder feedback)
8 = Setpoint frequency 23 = Actual frequency with slip, "Actual
frequency with slip"
(SW V2.0 and above)
9 = Error number 24 = Master value, actual freq. with slip,
"Master value, actual freq. with slip"
(SW V2.0 and above)
10 = ... 11 Reserved 53 = ... 57 Reserved
12 = BusIO Out Bits 0...7
Scaling details: Section: 8.8
Pos : 308 /Anleit ungen/5. / 6. Parametrier ung [BU 0500 / BU 0200]/ Par ameter/ P500-P599/ Paramet er P546 – Funkti on Bus-Soll wert e [SK 54xE] @ 0\mod_1328098077630_388. doc x @ 11939 @ @ 1
5
The assignment of the digital inputs in P543/ 544/ 545 = 5
Bit 0 = DigIn 1 Bit 1 = DigIn 2 Bit 2 = DigIn 3 Bit 3 = DigIn 4
Bit 4 = DigIn 5 Bit 5 = DigIn 6 (SK 520E and above) Bit 6 = DigIn 7 (SK 520E and above) Bit 7 = Dig. func. AIN1
Bit 8 = Dig. func. AIN1 AIN2 Bit 9 = DigIn 8 (SK 540E and above) Bit 10 = DigIn 1, 1.IOE (SK 540E and above) Bit 11 = DigIn 2, 1.IOE (SK 540E and above)
Bit 12 = Out 1/ MFR1 Bit 13 = Out 2/ MFR2 Bit 14 = Out 3/ DOUT1 (SK 520E and above) Bit 15 = Out 4/ DOUT2 (SK 520E and above)