HP LaserJet M4345 Multifunction Printer series - Manual (Page 191)

Control panel message Description Recommended action
13.JJ.NT JAM INSIDE TOP COVER AREA Media is jammed in the top cover area. Follow the instructions in the onscreen
dialog box. See
Clear jams from the top-
cover and print-cartridge areas .
13.JJ.NT JAM INSIDE TOP COVER AREA
Remove print cartridge Media is jammed in the top cover area and
you must remove the print cartridge to clear
the jam. Follow the instructions in the onscreen
dialog box. See
Clear jams from the top-
cover and print-cartridge areas .
13.JJ.NT JAM INSIDE TRAY 2 AREA Media is jammed in tray 2. Follow the instructions in the onscreen
dialog box. See
Clear jams from the tray2,
3, 4, or 5 areas .
13.JJ.NT JAM INSIDE TRAY 2 RIGHT
ACCESS DOOR Media is jammed inside tray 2 in the jam-
access door. Follow the instructions in the onscreen
dialog box.
13.JJ.NT JAMS INSIDE TOP COVER
AREA Remove print cartridge Media is jammed in more than one location
inside the top cover area. You must remove
the print cartridge to clear the jams. Follow the instructions in the onscreen
dialog box. See
Clear jams from the top-
cover and print-cartridge areas .
13.JJ.NT PAPER JAM OPEN INPUT
TRAYS Media is jammed inside one or more of the
trays. Follow the instructions in the onscreen
dialog box.
20 INSUFFICIENT MEMORY To continue
touch OK The MFP received more data than can fit in
the available memory. You might have tried
to transfer too many macros, soft fonts, or
complex graphics. Touch OK to print the transferred data
(some data might be lost), and then simplify
the print job or install additional memory.
See
Adding printer memory .
21 PAGE TOO COMPLEX To continue
touch OK The page formatting process was not fast
enough for the MFP. Touch OK to print the transferred data.
(Some data might be lost.) If this message
appears often, simplify the print job.
22 EIO X BUFFER OVERFLOW To
continue touch OK Too much data was sent to the EIO card in
the specified slot (x). An incorrect
communications protocol might be in use. Touch OK to print the transferred data.
(Some data might be lost.)
Check the host configuration. If this
message persists, contact an HP-
authorized service or support provider.
(See the HP support flyer, or go to
http://www.hp.com/support/ljm4345mfp .)
22 EMBEDDED I/O BUFFER OVERFLOW
To continue touch OK Too much data was sent to the embedded
HP Jetdirect print server. Touch OK to print the transferred data.
(Some data might be lost.)
30.1.YY SCANNER FAILURE An error has occurred in the scanner. Check the scanner lock. Turn the MFP off
and then on.
If this message persists, contact an HP-
authorized service or support provider.
(See the HP support flyer, or go to
http://www.hp.com/support/ljm4345mfp .)
40 BAD EIO X TRANSMISSION To
continue touch OK The connection between the MFP and the
EIO card in the specified slot has been
broken. Touch OK to clear the error message and
continue printing.
40 BAD SERIAL TRANSMISSION To
continue touch OK A serial data error (parity, framing, or line
overrun) occurred as data was being sent
by the computer. Touch OK to clear the error message.
(Data will be lost.)
40 EMBEDDED I/O BAD TRANSMISSION
To continue touch OK A temporary printing error has occurred. Turn the MFP off, and then turn the MFP on.
If this message persists, contact an HP-
authorized service or support provider.
(See the HP support flyer, or go to
http://www.hp.com/support/ljm4345mfp .)
Table 11-1 Control-panel messages (continued)
ENWW Control-panel messages 179